manualshive.com logo in svg

Honeywell NOTIFIER SCS Series, Руководство по эксплуатации и установке, Страница: 199 / 210

Поделиться
Скачать
Honeywell NOTIFIER SCS Series Скачать руководство пользователя страница 199

SCS Series Manual —

 P/N 15712:L  7/18/16

199

Programming Examples

AM2020/AFP1010 Control-By-Event

Example # 1

L1D1, L1D2, and L1D3 are first floor smoke detectors that acti-
vate Z1. L1D4 is a first floor elevator lobby smoke detector that 
activates Z2. If Z1 activates, control module L1M1 and L1M4 
will activate. Control module L1M1 could be used to close the 
supply damper to the floor during a fire condition. If Z2 acti-
vates then control module L1M4 will activate. Control module 
L1M4 could be used to turn on a fan to pressurize the elevator 
shaft. The equation AND(Z1 Z238) requires both to be active for 
an output. Because reverse Zone 238 has a NOT operand, it is 
active as long as L1D4 is inactive. So if there is smoke on the 
floor but not in the elevator lobby, Z239 activates and control 
module L1M2 is active.

Example # 2: General Alarm

L1D1 activates L1M1 through Z1. L1D2 activates 
L1M2 through Z2. L1D3 and L1D4 activate L1M4 
through Z3. L1M3 will activate when reverse zone 
239 is activated. Z239 will activate when Z1, Z2 or Z3 
are activated.

Notification Appliance L1M3 serves as the General 
Alarm device. It will be activated whenever an alarm 
occurs on any initiating device in the system, due to 
the fact that all initiating devices activate a Software 
Zone, and activation of any zone activates software 
zone Z239.

Z2

L1D1

RZON

Z240

L1D3

L1D4

RZON

Z239

L1D2

L1M2

L1M1

Z1

L1M4

RZON

Z239

AND(Z1 Z238)

RZON

Z238

(Z1)

(Z1)

(Z1)

NOT(Z2)

OR(Z1)

OR(Z239)

OR(Z1 Z2)

RZON

Z240

L1D1

Z2

L1D3

L1D4

Z3

L1D2

L1M2

L1M1

Z1

L1M4

L1M3

(Z1)

(Z2)

(Z3)

RZON

Z239

OR(Z1 Z2 Z3)

OR(Z1)

OR(Z2)

OR(Z239)

OR(Z3)

Содержание NOTIFIER SCS Series



















































































































































































































Отзывы:

Нет отзывов