Honeywell NOTIFIER SCS Series Скачать руководство пользователя страница 9

Страница: 9 / 210

SCS Series Manual —

P/N 15712:L 7/18/16

Section 1: About This Manual

1.1 Standards and Other Documents

This Fire Alarm Control Panel complies with the following NFPA standards:

NFPA 12 CO2 Extinguishing Systems

NFPA 12A Halon 1301 Extinguishing Systems

NFPA 13 Sprinkler Systems

NFPA 15 Water Spray Systems

NFPA 16 Foam/Water Deluge and Foam/Water Spray Systems

NFPA 17 Dry Chemical Extinguishing Systems

NFPA 17A Wet Chemical Extinguishing Systems

NFPA 72 Central Station Fire Alarm Systems (Automatic, Manual and Waterflow) Protected Premises Unit (requires Notifier UDACT).

NFPA 72 Local (Automatic, Manual, Waterflow and Sprinkler Supervisory) Fire Alarm Systems.

NFPA 72 Auxiliary (Automatic, Manual and Waterflow) Fire Alarm Systems (requires TM-4).

NFPA 72 Remote Station (Automatic, Manual and Waterflow) Fire Alarm Systems

NFPA 72 Proprietary (Automatic, Manual and Waterflow) Fire Alarm Systems (Protected Premises Unit).

NFPA 2001 Clean Agent Fire Extinguishing Systems

The installer should be familiar with the following documents and standards:

NFPA 72 Initiating Devices for Fire Alarm Systems

NFPA 72 Inspection, Testing and Maintenance for Fire Alarm Systems

NFPA 72 Notification Appliances for Fire Alarm Systems

Underwriters Laboratories

UL 38 Manually Actuated Signaling Boxes

UL 217 Smoke Detectors, Single and Multiple Station

UL 228 Door Closers - Holders for Fire Protective Signaling Systems

UL 268 Smoke Detectors for Fire Protective Signaling Systems

UL 268A Smoke Detectors for Duct Applications

UL 346 Waterflow Indicators for Fire Protective Signaling Systems

UL 464 Audible Signaling Appliances

UL 521 Heat Detectors for Fire Protective Signaling Systems

UL 864 Standard for Control Units for Fire Protective Signaling Systems

UL 1481 Power Supplies for Fire Protective Signaling Systems

UL 1971 Visual Signaling Appliances

UL 1076 Proprietary Burglar Alarm Systems

Underwriters Laboratories of Canada (ULC)

Standard CAN/ULC-S527-M99

CAN/ULC-S524-M91 Standard for the Installation of Fire Alarm Systems

Other

EIA-485 and EIA-232 Serial Interface Standards

NEC Article 300 Wiring Methods

NEC Article 760 Fire Protective Signaling Systems

Applicable Local and State Building Codes

Requirements of the Local Authority Having Jurisdiction

C22.1-98 The Canadian Electrical Code, Part 1

Содержание NOTIFIER SCS Series



















































































































































































































Результаты поиска

Содержание NOTIFIER SCS Series

Отзывы:

Honeywell NOTIFIER SCS Series, Руководство по эксплуатации и установке, Страница: 9 / 210

Результаты поиска

Содержание NOTIFIER SCS Series

Отзывы: