Honeywell NOTIFIER SCS Series Скачать руководство пользователя страница 35 | Manualshive

Страница: 35 / 210

Honeywell NOTIFIER SCS Series Скачать руководство пользователя страница 35

SCS Series Manual —

P/N 15712:L 7/18/16

35

Smoke Control Lamp Driver (SCS-8L)

The SCS⁄SCE

3.3 Smoke Control Lamp Driver (SCS-8L)

Each SCS-8L has two rotary decimal switches for addressing and 8 dipswitches for mode configuration (see Figure 3.2). The rotary switches
and dipswitches are not on the SCE-8L.

Each SCS-8L⁄SCE-8L module has eight independent switch groups that consist of the following:

•

Contacts for three position switch (ON/AUTO/OFF)

•

Four annunciator protocol points (two control and two monitor)

•

Contact for an On LED (Green)

•

Contact for an Off LED (Yellow)

•

Contact for a Trouble LED (Amber)

Each SCS-8L⁄SCE-8L also has contacts for two LEDs and one momentary switch with the following functions:

•

Contact for an All Auto LED (Green)

•

Contact for a Manual LED (Amber)

•

Contact for a Local Acknowledge/Lamp Test momentary switch

ON/OFF LED

(groups 1-4) Connector

All Auto/Manual LED

Connector

Local Acknowledge/Lamptest

Switch Connector

Security Keyswitch

Connector

ON/AUTO/OFF Switch

(groups 5-8) Connector

ON/AUTO/OFF Switch

(groups 1-4) Connector

EIA-485 Interface

Connection

Power Connection

ON/OFF LED
(groups 5-8) Connector

Trouble LED
(groups 1-8) Connector

+5 VDC LED
Power Connector

+24 VDC LED
Power Connector

+24 VDC Relay Power

SCE-8L Smoke Control
Expander Connector

Rotary Decimal
Address Switches

8 Dipswitches

SC

S-

8

L

.W

M

F

Figure 3.2 SCS-8L

«
...
33
34
35
36
37
...
»

Содержание NOTIFIER SCS Series



















































































































































































































Отзывы:

Нет отзывов