Honeywell NOTIFIER SCS Series Скачать руководство пользователя страница 178

Страница: 178 / 210

178

SCS Series Manual —

P/N 15712:L 7/18/16

Ratings and Wiring Diagrams

HVAC Wiring Diagrams

Figure 5.70 EP Damper Control - HVAC Switch Group Type 4

Figure 5.70 depicts an EP damper in an HVAC system with the capability of

CLOSED

control, switch group type 4. In the above configura-

tion, the CON

OFF⁄CL

CM is activated. The CON

OFF⁄CL

CM controls a normally open contactor for the pressure switch power line. When the

CON

OFF⁄CL

CM is activated, the normally open contactor is closed. When the contactor closes, power is supplied to the pressure switch

which cuts the airflow to the damper, closing the damper. When the CON

OFF⁄CL

CM is deactivated, the EMS is free to control the damper.

The EMS is currently being overridden by the CON

OFF⁄CL

CM.

Airflow

PRESSURE

SWITCH

SMOKE

DAMPER

CLOSED

Power Source

Listed

24 VDC

Power Source

SLC Loop

FCM-1

CON

OFF/CL

(activated)

A-

fs-

Power

Return

Pneumatic

Tubing

Energy

Management

System

1a listed
contactor

*If the SLC device
does not match the
one in this figure,
refer to the SLC
manual appendix,
which contains
wiring conversion
charts for type V
and type H
modules.

Содержание NOTIFIER SCS Series



















































































































































































































Результаты поиска

Содержание NOTIFIER SCS Series

Отзывы:

Honeywell NOTIFIER SCS Series, Руководство по эксплуатации и установке, Страница: 178 / 210

Результаты поиска

Содержание NOTIFIER SCS Series

Отзывы: