Honeywell NOTIFIER SCS Series Скачать руководство пользователя страница 149

Страница: 149 / 210

SCS Series Manual —

P/N 15712:L 7/18/16

149

Non-dedicated Smoke Control System Wiring Diagrams

Ratings and Wiring Diagrams

Figure 5.40 EP Damper Control, Non-dedicated System - FSCS Switch Group Type 9

Figure 5.40 depicts an EP damper in a non-dedicated system with the capability of

OPEN

and

CLOSED

control and verification of the

OPEN

and

CLOSED

state, switch group type 9. In the above configuration, the CON

ON⁄OP

CM is activated and the CON

OFF⁄CL

CM is deactivated. The

CON

ON⁄OP

CM controls a normally closed contactor for the pressure switch power line. When the CON

ON⁄OP

CM is activated, the normally

closed contactor is opened. When the contactor opens, power is cut from the pressure switch, which allows airflow to open the damper.
When the CON

ON⁄OP

CM is deactivated, the EMS is free to control the damper. The EMS is currently being overridden by the

CON

ON⁄OP

CM.

When power is cut from the pressure switch, the damper opens. When the damper completely opens, the damper open limit switch is

CLOSED

and the damper closed limit switch is

OPEN

, indicating that the damper is in the

OPEN

position. The VER

ON⁄OP

MM monitors the

CLOSED

position of the damper open limit switch and the VER

OFF⁄CL

MM monitors the

CLOSED

position of the damper closed limit switch. In this

case the VER

ON⁄OP

MM is activated and the VER

OFF⁄CL

MM is deactivated because the damper is

OPEN

FMM-1

Airflow

PRESSURE

SWITCH

SMOKE

DAMPER

OPEN

Power Source

Listed
24 VDC
Power Source

SLC Loop

FCM-1

CON

OFF/CL

(deactivated)

-NF9

-f

2.wm

Power Return

VER

OFF⁄CL

(deactivated)

N/O

COM

Limit Switch
for closed
position

ELR-47K

(use 3.9K listed ELR with FZM-1)

Pneumatic

Tubing

Energy
Management
System

1a listed

contact

N/O

COM

Limit Switch

for open

position

VER

ON⁄OP

(activated)

FMM-1

1b listed

contact

FRM-1

CON

ON/OP

(activated)

*If the SLC device
does not match the
one in this figure,
refer to the SLC
manual appendix,
which contains
wiring conversion
charts for type V
and type H
modules.

Содержание NOTIFIER SCS Series



















































































































































































































Результаты поиска

Содержание NOTIFIER SCS Series

Отзывы:

Honeywell NOTIFIER SCS Series, Руководство по эксплуатации и установке, Страница: 149 / 210

Результаты поиска

Содержание NOTIFIER SCS Series

Отзывы: