manualshive.com logo in svg

Honeywell NOTIFIER SCS Series, Руководство по эксплуатации и установке, Страница: 163 / 210

Поделиться
Скачать
Honeywell NOTIFIER SCS Series Скачать руководство пользователя страница 163

SCS Series Manual —

 P/N 15712:L  7/18/16

163

HVAC Wiring Diagrams

Ratings and Wiring Diagrams

Figure 5.54  Motorized Damper Control - HVAC Switch Group Type 3

Figure 5.54 depicts a motorized damper in an HVAC system with the capability of verification of the 

OPEN

 and 

CLOSED

 state, switch group 

type 3. In the above configuration, the EMS is supplying power to the damper closed power line. When power is supplied to the damper 
closed power line, the damper closes. When the damper completely closes, the damper closed limit switch is 

CLOSED

, indicating that the 

damper is in the 

CLOSED

 position. The VER

OFF⁄CL

MM monitors the 

CLOSED

 position of the damper closed limit switch and the 

VER

ON⁄OP

MM monitors the 

CLOSED

 position of the damper open limit switch. In this case the VER

OFF⁄CL

MM is activated and the 

VER

ON⁄OP

MM is deactivated because the damper is 

CLOSED

.

Power Source

Damper

Open

Power

ELR-47K

(use 3.9K listed ELR with FZM-1)

N/O

COM

Power Return

FMM-1

DM

O-

h3a

-fs-

2

.wm

f

SLC Loop

VER

OFF/CL

MM

(activated)

Limit Switch
for closed 
position

Damper
Closed
Power

AC 

MOTOR

DAMPER

CLOSED

Energy 

Management

System

FMM-1

VER

ON⁄OP

MM

(deactivated)

N/O

COM

Limit Switch

for open 

position

*If the SLC device 
does not match the 
one in this figure, 
refer to the SLC 
manual appendix, 
which contains 
wiring conversion 
charts for type V 
and type H 
modules.

Содержание NOTIFIER SCS Series



















































































































































































































Отзывы:

Нет отзывов