Honeywell NOTIFIER SCS Series Скачать руководство пользователя страница 155

Страница: 155 / 210

SCS Series Manual —

P/N 15712:L 7/18/16

155

HVAC Wiring Diagrams

Ratings and Wiring Diagrams

Figure 5.46 Fan Control - HVAC Switch Group Type 8

Figure 5.46 depicts a fan in an HVAC system with the capability of

control, switch group type 8. In the above configuration, the

CON

ON⁄OP

CM is deactivated. The CON

ON⁄OP

CM is wired in parallel with the EMS. (When wired in parallel with the EMS, use a relay

module.) When the CON

ON⁄OP

CM is deactivated, the EMS is free to control the fan. In this case the EMS is

OFF

, so no power is being sup-

plied to the fan. When no power is supplied to the fan, the fan is

OFF

. When the CON

ON⁄OP

CM is activated, the CON

ON⁄OP

CM overrides

whatever state the EMS is in and closes the normally open contactor, thus supplying power to the fan and turning it on.

FRM-1

COM

N/O.

Power Source

1a listed

contactor

Service

Disconnect

Switch

Power Return

-f

-2

.wm

SLC Loop

FAN OFF

Listed
24 VDC
Power Source

CON

ON/OP

(deactivated)

Energy Management System

*If the SLC device
does not match the
one in this figure,
refer to the SLC
manual appendix,
which contains wiring
conversion charts for
type V and type H
modules. e

Содержание NOTIFIER SCS Series



















































































































































































































Результаты поиска

Содержание NOTIFIER SCS Series

Отзывы:

Honeywell NOTIFIER SCS Series, Руководство по эксплуатации и установке, Страница: 155 / 210

Результаты поиска

Содержание NOTIFIER SCS Series

Отзывы: