Honeywell NOTIFIER SCS Series Скачать руководство пользователя страница 171 | Manualshive

Страница: 171 / 210

Honeywell NOTIFIER SCS Series Скачать руководство пользователя страница 171

SCS Series Manual —

P/N 15712:L 7/18/16

171

HVAC Wiring Diagrams

Ratings and Wiring Diagrams

Figure 5.62 Motorized Damper Control - HVAC Switch Group Type 11

Figure 5.62 depicts a motorized damper in an HVAC system with the capability of

OPEN

control and verification of the

OPEN

and

CLOSED

state, switch group type 11. In the above configuration, the CON

ON⁄OP

CM is activated. The CON

ON⁄OP

CM controls two contactors: a nor-

mally closed contactor for the damper closed power line, and a dual normally open/normally closed contactor for the damper open power
line. When the CON

ON⁄OP

CM is activated, the normally closed contactor is opened (cutting any power supplied by the EMS to the damper

closed power line), the normally closed portion of the dual contactor is opened (cutting any power supplied by the EMS to the damper open
power line), and the normally open portion of the dual contactor is closed, thus supplying power to close the damper. When the
CON

ON⁄OP

CM is deactivated, the EMS is free to control the damper. The EMS is currently being overridden by the CON

ON⁄OP

CM.

When power is supplied to the damper open power line, the damper opens. When the damper completely opens, the damper open limit
switch is

CLOSED

, indicating that the damper is in the

OPEN

position.

The VER

OFF⁄CL

MM monitors the

CLOSED

position of the damper closed limit switch and the VER

ON⁄OP

MM monitors the

CLOSED

position

of the damper open limit switch. In this case the VER

OFF⁄CL

MM is deactivated and the VER

ON⁄OP

MM is activated because the damper is

OPEN

.

Power Source

Damper

Open

Power

ELR-47K

(use 3.9K listed ELR with FZM-1)

N/O

COM

Power Return

Listed

24 VDC

Power Source

FMM-1

D

M

O-

h1

1a

-fs

-2

.w

m

f

SLC Loop

CON

ON/OP

CM

(activated)

VER

OFF/CL

MM

(deactivated)

Limit Switch
for closed
position

Damper
Closed
Power

AC

MOTOR

DAMPER

OPEN

FCM-1

1a, 1b listed contact

1b listed

contact

Energy

Management

System

FMM-1

VER

ON⁄OP

MM

(activated)

N/O

COM

Limit Switch

for open

position

*If the SLC device
does not match the
one in this figure,
refer to the SLC
manual appendix,
which contains
wiring conversion
charts for type V
and type H
modules.

«
...
169
170
171
172
173
...
»

Содержание NOTIFIER SCS Series



















































































































































































































Отзывы:

Нет отзывов