manualshive.com logo in svg

Honeywell NOTIFIER SCS Series, Руководство по эксплуатации и установке, Страница: 33 / 210

Поделиться
Скачать
Honeywell NOTIFIER SCS Series Скачать руководство пользователя страница 33

SCS Series Manual —

 P/N 15712:L  7/18/16

33

Smoke Control Station (SCS-8)

The SCS⁄SCE

  

3.1.2  SCS V4.0 Software Features 

This manual describes versions 2.84 and 4.0 of the SCS-8/SCS-8L; the table below specifies which features are available only to version 4.0 
and higher. 

To use the version 4.0 features, the smoke control station must be connected to NFS2-3030, or NCA-2 running software V21 or higher.

3.2  Smoke Control Station (SCS-8)

Each SCS-8 has two rotary decimal switches for addressing and 8 dipswitches for mode configuration (see Figure 3.1). The rotary switches 
and dipswitches are not on the SCE-8. 

Each SCS-8⁄SCE-8 module has eight independent switch groups that consist of the following (see Figure 3.1): 

•

Miniature locking toggle switch - three position ON/AUTO/OFF (OPEN/AUTO/CLOSE)

•

Four annunciator protocol points (two control and two monitor)

•

Green On (Open) LED

•

Yellow Off (Closed) LED 

•

Amber Trouble LED

Each SCS-8⁄SCE-8 also has two LEDs and one momentary switch with the following functions (see Figure 3.1): 

•

Green All Auto LED

•

Amber Manual

•

Local Acknowledge/Lamp Test momentary switch 

NOTE:

1. Software Part Numbers 73631 and 73845 are not compatible with INA combinations after M2.7. 
2. Part #SCSV2.84 is not compatible with FACP/INA combinations prior to M2.8.
3. NFS-320s, NFS2-640s, NFS-640s, NFS2-3030s, NFS-3030s, NCAs and NCA-2s are only compatible with software #SCS2.84 or higher. 
(They are not compatible with any 73XXX series software versions.)
4. To use the SCS V4.0, NFS2-3030, and/or NCA-2 must be running software V21 or higher. 

Table 3.2  SCS Features: V2.84 vs V4.0

Panel Feature (V21.0) 

FSCS Mode A**

FSCS Mode B**

SCS-8/8L V2.84

SCS-8/8L V4.0

SCS-8/8L V4.0

Independent Switch-group Operation 

(See Appendix C.2, “Mode B Operation”) 

No

No

Yes

Multiple Smoke Control Station 

No

Yes

Yes

Pairing No

Yes

No

Programmable Trouble Timer*  

No

Yes

Yes

SCS Logic Equation Operators* 

No

Yes

Yes

Enhanced Trouble Reporting* 

No

Yes

Yes

*See NFS2-3030/NCA-2 documentation. 
**See NFS2-3030/NCA-2 documentation for mode setting. 

Содержание NOTIFIER SCS Series



















































































































































































































Отзывы:

Нет отзывов