Honeywell NOTIFIER SCS Series Скачать руководство пользователя страница 42 | Manualshive

Страница: 42 / 210

Honeywell NOTIFIER SCS Series Скачать руководство пользователя страница 42

42

SCS Series Manual —

P/N 15712:L 7/18/16

The SCS⁄SCE

Cabinet and Chassis Mounting

3.5 Cabinet and Chassis Mounting

Select an appropriate knockout on the enclosure. Mount the cabinet or backbox.
Ground the enclosure to a solid metallic ground, such as a grounded cold water
pipe. Pull all SCS-8 wiring into the enclosure as illustrated in Figure 3.6.

ABS-4D Backbox

The ABS-4D may be surface mounted or semi-flush mounted. Five knockouts are
provided on the top of the box, five on the bottom and three on the back surface.
Six mounting holes are provided on the back surface and two on each side. Back-
box and door dimensions, as well as the spacing of the mounting holes and knock-
outs, are provided in document number 15073, ABS-4D Product Installation
Drawing.

CAB-3, CAB-4 Cabinets

The CAB-3 and CAB-4 Cabinet series are available in four sizes (A through D).
A trim ring is available for semi-flush mounting. Backbox and door dimensions,
as well as the spacing of the mounting holes and knockouts, for all four sizes of
these cabinets are provided in document number 15330, CAB-3/CAB-4 Installa-
tion Drawing.

CHS-4L Chassis

If a CHS-4L is to be used for installing the SCS-8L⁄SCE-8L, mount the chassis to
the cabinet and secure with the hardware provided, as illustrated in Figure 3.7. A
Grounding Cable Assembly may be connected to the chassis mounting stud for
connection to the module's Earth Ground terminal.

For each SCS-8L⁄SCE-8L module to be installed on the chassis, connect two
female-to-female standoffs (provided) to the upper mounting studs on the chassis,
as shown in Figure 3.8.

Custom Graphic Annunciator Cabinets

Follow the instructions from the graphic annunciator manufacturer if installation
is in a graphic annunciator cabinet.

Figure 3.6 Installing the Enclosure

Figure 3.7 Mounting the Chassis

C

G

Figure 3.8 Board Standoffs

«
...
40
41
42
43
44
...
»

Содержание NOTIFIER SCS Series



















































































































































































































Отзывы:

Нет отзывов