Honeywell NOTIFIER SCS Series Скачать руководство пользователя страница 131 | Manualshive

Страница: 131 / 210

Honeywell NOTIFIER SCS Series Скачать руководство пользователя страница 131

SCS Series Manual —

P/N 15712:L 7/18/16

131

Non-dedicated Smoke Control System Wiring Diagrams

Ratings and Wiring Diagrams

Figure 5.22 Fan Control, Non-dedicated System - FSCS Switch Group Type 8

Figure 5.22 depicts a fan in a non-dedicated system with the capability of

ON

and

OFF

control and verification of the

ON

state, switch group

type 8. In the above configuration, the CON

ON⁄OP

CM is deactivated and the CON

OFF⁄CL

CM is deactivated. These two control modules are

always in the opposite state when the smoke control system is in operation and are always deactivated during normal operation. The
CON

ON⁄OP

CM is wired in parallel with the EMS; when wired in parallel with the EMS the CM must be a relay module. When the

CON

ON⁄OP

CM and the CON

OFF⁄CL

CM are deactivated, the EMS is free to control the fan. In this case the EMS is

OFF

, so no power is being

supplied to the fan. When no power is supplied to the fan, the fan is

OFF

and the sail switch is

CLOSED

, indicating no airflow in the duct. The

VER

ON⁄OP

MM monitors the

OPEN

position of the sail switch, which would indicate when the fan is

ON

. In this case the VER

ON⁄OP

MM is

deactivated because the fan is

OFF

due to the EMS. When the CON

ON⁄OP

CM is activated for smoke control, the CON

ON⁄OP

CM overrides

whatever state the EMS is in and closes the normally open contactor, thus supplying power to the fan and turning it

ON

. When the

CON

OFF⁄CL

CM is activated for smoke control, the CON

OFF⁄CL

CM opens the normally closed contactor and turns the fan

OFF

, overriding

whatever state the EMS is in.

Switch group type 9 is used for

ON

and

OFF

control and verification of the

ON

and

OFF

state. Since it is possible to determine both

ON

and

OFF

verification from switch group type 7 or switch group type 8, switch group type 9 would only be necessary for redundancy in verifying the
state of the fan. For example, if switch group type 7 is used instead of switch group type 8, the

OFF

state of the fan would be verified when

the monitor module is activated and the

ON

state of the fan would be verified when the monitor module is deactivated. Utilizing switch group

types 7 or 8 also saves the use of an additional monitor module. Switch group type 9 would use two monitor modules to provide the same
verification as types 7 or 8.

Power Source

Service

Disconnect

Switch

ELR-47K

(use 3.9K listed ELR with FZM-1)

Listed

Sail

Switch

N/O

COM

N/C

Power Return

VER

OFF/CL

MM

(deactivated)

fa

n-

n

f8-

fs-

2

.w

m

f

SLC Loop

FAN OFF

Energy
Management
System

Listed

24 VDC

Power Source

FMM-1

CON

ON/OP

CM

(deactivated)

FRM-1

1a listed

contactor

1b listed

contactor

Listed

24 VDC

Power Source

FCM-1

CON

OFF/CL

CM

(deactivated)

*If the SLC device
does not match the
one in this figure, refer
to the SLC manual
appendix, which
contains wiring
conversion charts for
type V and type H
modules.

«
...
129
130
131
132
133
...
»

Содержание NOTIFIER SCS Series



















































































































































































































Отзывы:

Нет отзывов