Honeywell NOTIFIER SCS Series Скачать руководство пользователя страница 115 | Manualshive

Страница: 115 / 210

Honeywell NOTIFIER SCS Series Скачать руководство пользователя страница 115

SCS Series Manual —

P/N 15712:L 7/18/16

115

Dedicated Smoke Control System Wiring Diagrams

Ratings and Wiring Diagrams

Figure 5.7 Motorized Damper Control

Dedicated System - FSCS Switch Group Type3

Figure 5.7 depicts a motorized damper in a dedicated system with the capability of

CLOSED

control and verification of the

OPEN

and

CLOSED

state, switch group type 3. In the above configuration, the CON

OFF⁄CL

CM is activated. The CON

OFF⁄CL

CM controls a normally closed con-

tactor for the damper open power line and a normally open contactor for the damper close power. When the CON

OFF⁄CL

CM is activated, the

normally closed contactor is opened and the normally open contactor is closed, thus supplying power to close the damper. When the damper
completely closes, the damper closed limit switch is closed, indicating that the damper is in the

CLOSED

position. (When the damper is in the

open position, the damper open limit switch is closed.) The VER

OFF⁄CL

MM monitors when the damper closed limit switch is

CLOSED

. In this

case the VER

OFF⁄CL

MM is activated and the VER

ON⁄OP

MM is deactivated because the damper is

CLOSED

.

Damper

Open

Power

N/O

COM

Damper
Closed
Power

AC

MOTOR

DAMPER

CLOSED

Limit Switch

for open

position

1a listed

contactor

1b listed

contactor

Power Source

Listed

24 VDC

Power Source

SLC Loop

ELR-47K

(use 3.9K listed ELR with FZM-1)

FCM-1

VER

ON⁄OP

MM

(activated)

CON

OFF/CL

CM

(activated)

D

M

O-

df

3

-f

s

-2

.w

mf

FMM-1

VER

OFF⁄CL

MM

(deactivated)

FMM-1

N/O

COM

Limit Switch
for closed
position

Power Return

*If the SLC device
does not match the
one in this figure,
refer to the SLC
manual appendix,
which contains
wiring conversion
charts for type V
and type H
modules.

«
...
113
114
115
116
117
...
»

Содержание NOTIFIER SCS Series



















































































































































































































Отзывы:

Нет отзывов