manualshive.com logo in svg

Honeywell NOTIFIER SCS Series, Руководство по эксплуатации и установке, Страница: 135 / 210

Поделиться
Скачать
Honeywell NOTIFIER SCS Series Скачать руководство пользователя страница 135

SCS Series Manual —

 P/N 15712:L  7/18/16

135

Non-dedicated Smoke Control System Wiring Diagrams

Ratings and Wiring Diagrams

Figure 5.26  Motorized Damper Control

 Non-dedicated System - FSCS Switch Group Type 4

Figure 5.26 depicts a motorized damper in a non-dedicated system with the capability of 

OPEN

 control and verification of the 

CLOSED

 state, 

switch group type 4. In the above configuration, the CON

ON⁄OP

CM is activated. The CON

ON⁄OP

CM controls two contactors: a normally 

closed contactor for the damper closed power line, and a dual normally open/normally closed contactor for the damper open power line. 
When the CON

ON⁄OP

CM is activated, the normally closed contactor is opened (cutting any power supplied by the EMS to the damper closed 

power line), the normally closed portion of the dual contactor is opened (cutting any power supplied by the EMS to the damper open power 
line), and the normally open portion of the dual contactor is closed, thus supplying power to close the damper. When the CON

ON⁄OP

CM is 

deactivated, the EMS is free to control the damper. The EMS is currently being overridden by the CON

ON⁄OP

CM.

When power is supplied to the damper open power line, the damper opens. When the damper completely opens, the damper open limit 
switch is 

CLOSED

, indicating that the damper is in the 

OPEN

 position. The VER

OFF⁄CL

MM monitors the 

CLOSED

 position of the damper closed 

limit switch. In this case the VER

OFF⁄CL

MM is deactivated because the damper is 

OPEN

.

Power Source

1b, 1a listed contactor

Damper

Open

Power

ELR-47K

(use 3.9K listed ELR with FZM-1)

N/O

COM

Power Return

Listed 

24 VDC

Power Source

FMM-1

dm

o-

nf

4a

-f

s

-2

.wmf

SLC Loop

1a listed

contactor

CON

ON/OP

CM

(activated)

VER

OFF/CL

MM

(activated)

Limit Switch
for closed 
position

Damper
Closed
Power

AC 

MOTOR

DAMPER

OPEN

FCM-1 

Energy 

Management

System

*If the SLC device 
does not match the 
one in this figure, 
refer to the SLC 
manual appendix, 
which contains 
wiring conversion 
charts for type V and 
type H modules.

Содержание NOTIFIER SCS Series



















































































































































































































Отзывы:

Нет отзывов