Honeywell NOTIFIER SCS Series Скачать руководство пользователя страница 127 | Manualshive

Страница: 127 / 210

Honeywell NOTIFIER SCS Series Скачать руководство пользователя страница 127

SCS Series Manual —

P/N 15712:L 7/18/16

127

Non-dedicated Smoke Control System Wiring Diagrams

Ratings and Wiring Diagrams

Figure 5.18 Fan Control, Non-dedicated System - FSCS Switch Group Type 2

Figure 5.18 depicts a fan in a non-dedicated system with the capability of

OFF

control and verification of the

ON

state, switch group type 2. In

the above configuration, the CON

OFF⁄CL

CM is deactivated. The CON

OFF⁄CL

CM controls a normally closed contactor which switches power

to the fan (the contactor is used when the power being switched is greater than 24 volts). When the CON

OFF⁄CL

CM is deactivated, the con-

tactor is closed, thus allowing the EMS to freely control the fan. In this case the EMS is

OFF

, so no power is being supplied to the fan. When

no power is supplied to the fan, the fan is

OFF

and the sail switch is

CLOSED

, indicating no airflow in the duct. The VER

ON⁄OP

MM monitors

the

OPEN

position of the sail switch, which would indicate when the fan is

ON

. In this case the VER

ON⁄OP

MM is deactivated because the fan

is

OFF

due to the EMS. When the CON

OFF⁄CL

CM is activated, the normally closed contactor opens, thus cutting any power to the fan that

was being supplied by the EMS.

Switch group type 3 is for a fan that would require the capability of

OFF

control and verification of both the

ON

and

OFF

states. Since it is pos-

sible to determine this information from either switch group type 1 or switch group type 2, switch group type 3 would only be necessary for
redundancy in verifying the state of the fan. For example, if switch group type 1 is used instead of switch group type 3, the

OFF

state of the

fan would be verified when the monitor module is activated and the

ON

state of the fan would be verified when the monitor module is deac-

tivated. Utilizing switch group types 1 or 2 also saves the use of an additional monitor module. Switch group type 3 would use two monitor
modules to provide the same verification as types 1 or 2.

Power Source

1b listed

contactor

Service

Disconnect

Switch

ELR-47K

(use 3.9K listed ELR with FZM-1)

Listed

Sail

Switch

N/O

COM

N/C

Power Return

Listed

24 VDC

Power Source

FCM-1

CON

OFF/CL

CM

(deactivated)

VER

ON/OP

MM

(deactivated)

fa

n-

nf

2-

fs-

2

.w

m

f

SLC Loop

FAN OFF

Listed contactor

for Energy

Management

System

Energy Management System

Listed

24 VDC

Power Source

FMM-1

*If the SLC device does
not match the one in
this figure, refer to the
SLC manual appendix,
which contains wiring
conversion charts for
type V and type H
modules.

«
...
125
126
127
128
129
...
»

Содержание NOTIFIER SCS Series



















































































































































































































Отзывы:

Нет отзывов