Honeywell NOTIFIER SCS Series Скачать руководство пользователя страница 144

Страница: 144 / 210

144

SCS Series Manual —

P/N 15712:L 7/18/16

Ratings and Wiring Diagrams

Non-dedicated Smoke Control System Wiring Diagrams

Figure 5.35 EP Damper Control, Non-dedicated System - FSCS Switch Group Type 4

Figure 5.35 depicts an EP damper in a non-dedicated system with the capability of

OPEN

control and verification of the

CLOSED

state, switch

group type 4. In the above configuration, the CON

ON⁄OP

CM is activated. The CON

ON⁄OP

CM controls a normally closed contactor for the

pressure switch power line. When CON

ON⁄OP

CM is activated, the normally closed contactor is opened. When the contactor opens, power is

cut from the pressure switch, which allows airflow to open the damper. When the CON

ON⁄OP

CM is deactivated, the EMS is free to control

the damper. The EMS is currently being overridden by the CON

ON⁄OP

CM.

When power is cut from the pressure switch, the damper opens. When the damper completely opens, the damper open limit switch is

CLOSED

and the damper closed limit switch is

OPEN

, indicating that the damper is in the

OPEN

position. The VER

OFF⁄CL

MM monitors the

CLOSED

position of the limit switch. In this case the VER

OFF⁄CL

MM is deactivated because the damper is

OPEN

FMM-1

Airflow

PRESSURE

SWITCH

SMOKE

DAMPER

OPEN

Power

Source

Listed
24 VDC
Power Source

SLC Loop

P-

4A-

-2.

Power

Return

VER

OFF⁄CL

(deactivated)

N/O

COM

Limit Switch
for closed
position

ELR-47K

(use 3.9K listed ELR with FZM-1)

Pneumatic

Tubing

Energy
Management
System

1b listed
contact

FRM-1

CON

ON/OP

(activated)

*If the SLC device
does not match the
one in this figure, refer
to the SLC manual
appendix, which
contains wiring
conversion charts for
type V and type H
modules.

Содержание NOTIFIER SCS Series



















































































































































































































Результаты поиска

Содержание NOTIFIER SCS Series

Отзывы:

Honeywell NOTIFIER SCS Series, Руководство по эксплуатации и установке, Страница: 144 / 210

Результаты поиска

Содержание NOTIFIER SCS Series

Отзывы: