manualshive.com logo in svg

Honeywell NOTIFIER SCS Series, Руководство по эксплуатации и установке, Страница: 140 / 210

Поделиться
Скачать
Honeywell NOTIFIER SCS Series Скачать руководство пользователя страница 140

140

SCS Series Manual —

 P/N 15712:L  7/18/16

Ratings and Wiring Diagrams

Non-dedicated Smoke Control System Wiring Diagrams

Figure 5.31  Motorized Damper Control

 Non-dedicated System - FSCS Switch Group Type 9

Figure 5.31 depicts a motorized damper in a non-dedicated system with the capability of 

OPEN

 and 

CLOSED

 control and verification of the 

OPEN

 and 

CLOSED

 state, switch group type 9. In the above configuration, the CON

ON⁄OP

CM is activated and the CON

OFF⁄CL

CM is deacti-

vated. Under normal operation (non-smoke control mode) both control modules would be deactivated, allowing the EMS system to freely 
control the damper. The CON

ON⁄OP

CM controls two contactors: a normally closed contactor for the damper closed power line, and a dual 

normally open/normally closed contactor for the damper open power line. The CON

OFF⁄CL

CM controls two contactors: a normally closed 

contactor for the damper open power line, and a dual normally open/normally closed contactor for the damper close power line. When the 
CON

ON⁄OP

CM is activated, the CON

OFF⁄CL

CM is deactivated, and vice versa. When the CON

ON⁄OP

CM is activated, the normally closed 

contactor is opened (cutting any power supplied by the EMS to the damper closed power line), the normally closed portion of the dual con-
tactor is opened (cutting any power supplied by the EMS to the damper open power line), and the normally open portion of the dual contac-
tor is closed, thus supplying power to open the damper.

When power is supplied to the damper open power line, the damper opens. When the damper completely opens, the damper open limit 
switch is 

CLOSED

 and the damper closed switch 

OPEN

s, indicating that the damper is in the 

OPEN

 position. The VER

ON⁄OP

MM monitors the 

CLOSED

 position of the damper open limit switch and the VER

OFF⁄CL

MM monitors the 

CLOSED

 position of the damper closed limit switch. In 

this case, the VER

ON⁄OP

MM is activated and the VER

OFF⁄CL

MM is deactivated because the damper is 

OPEN

.

Power Source

Damper

Open

Power

ELR-47K

(use 3.9K listed ELR with FZM-1)

N/O

COM

Power Return

Listed 

24 VDC

Power Source

FMM-1

D

M

O

-nf

9

a

-f

s

-2.

wm

f

SLC Loop

CON

ON/OP

CM

(activated)

VER

OFF/CL

MM

(deactivated)

Limit Switch
for closed 
position

Damper
Closed
Power

AC 

MOTOR

DAMPER

OPEN

FCM-1 

FCM-1

CON

OFF/CL

CM

(deactivated)

1a, 1b listed contact

1b listed

contact

Energy 

Management

System

1b listed contact

1b, 1a listed

contact

FMM-1

VER

ON⁄OP

MM

(activated)

N/O

COM

Limit Switch

for open 

position

*If the SLC device 
does not match the 
one in this figure, 
refer to the SLC 
manual appendix, 
which contains 
wiring conversion 
charts for type V 
and type H modules.

Содержание NOTIFIER SCS Series



















































































































































































































Отзывы:

Нет отзывов