manualshive.com logo in svg

Honeywell NOTIFIER SCS Series, Руководство по эксплуатации и установке, Страница: 119 / 210

Поделиться
Скачать
Honeywell NOTIFIER SCS Series Скачать руководство пользователя страница 119

SCS Series Manual —

 P/N 15712:L  7/18/16

119

Dedicated Smoke Control System Wiring Diagrams

Ratings and Wiring Diagrams

ity could be obtained by connecting one normally open contactor and one normally closed contactor to the output of one control module. For 
instance, if you are using one CON

OFF⁄CL

CM, connect the normally open contactor to the damper closed power and connect the normally 

closed contactor to the damper open power. Both control modules are not necessary to switch the power to the damper: one is sufficient for a 
dedicated system as long as two contactors are used. 

Switch group type 8 would never be needed unless redundancy in 

OFF

 and 

ON

 control were necessary. Type 8 is used for 

ON

 and 

OFF

 control 

and verification of the 

ON

 state. When the CON

ON⁄OP

CM is deactivated, the 

CON

OFF⁄CL

CM is activated, and vice versa. The CON

ON⁄OP

CM controls a normally open contactor which switches the damper open power 

to the damper. The CON

OFF⁄CL

CM controls a normally open contactor which switches damper close power to the damper. When the 

CON

ON⁄OP

CM is deactivated, the contactor is open, thus, cutting damper open power to the damper. When the CON

OFF⁄CL

CM is activated, 

the contactor is closed, thus supplying power to the fan. The same capability could be obtained by connecting one normally open contactor 
and one normally closed contactor to the output of one control module. For instance, if you are using one CON

OFF⁄CL

CM, connect the nor-

mally open contactor to the damper closed power and connect the normally closed contactor to the damper open power. Both control mod-
ules are not necessary to switch the power to the damper: one is sufficient for a dedicated system as long as two contactors are used.

Switch group type 9 would never be needed unless redundancy in 

OFF

 and 

ON

 control were necessary. Type 9 is used for 

ON

 and 

OFF

 control 

and verification of the 

ON

 and 

OFF

 state. When the CON

ON⁄OP

CM is deactivated, the CON

OFF⁄CL

CM is activated, and vice versa. The 

CON

ON⁄OP

CM controls a normally open contactor which switches the damper open power to the damper. The CON

OFF⁄CL

CM controls a 

normally open contactor which switches damper close power to the damper. When the CON

ON⁄OP

CM is deactivated, the contactor is open, 

thus cutting damper open power to the damper. When the CON

OFF⁄CL

CM is activated, the contactor is closed, thus supplying power to the 

fan. The same capability could be obtained by connecting one normally open contactor and one normally closed contactor to the output of 
one control module. For instance, if you are using one 

CON

OFF⁄CL

CM, connect the normally open contactor to the damper closed power and connect the normally closed contactor to the damper 

open power. Both control modules are not necessary to switch the power to the damper: one is sufficient for a dedicated system as long as 
two contactors are used.

5.3.3  EP Dampers

The Electrical to Pressure (EP) damper uses airflow to operate the opening and closing of the damper. It operates such that when power is 
applied to the pressure switch, airflow going to the damper is cut off and the damper closes. When no power is supplied to the pressure 
switch, airflow is continuous and keeps the damper open.

Содержание NOTIFIER SCS Series



















































































































































































































Отзывы:

Нет отзывов