Honeywell NOTIFIER SCS Series Скачать руководство пользователя страница 62 | Manualshive

Страница: 62 / 210

Honeywell NOTIFIER SCS Series Скачать руководство пользователя страница 62

62

SCS Series Manual —

P/N 15712:L 7/18/16

The SCS⁄SCE

Configuration

Switch Group LEDs for FSCS Mode



FSCS Toggle Switch Group LEDs

There are three LEDs associated with each SCS⁄SCE toggle switch. These LEDs function according to Table 3.8.



FSCS Trouble Conditions

When an SCS⁄SCE trouble condition exists, the type of trouble can be identified on the SCS⁄SCE modules by a series of one or more LED
flashes (trouble codes) as described in this section.



FSCS Module Trouble

A trouble affecting the entire SCS⁄SCE is called a module trouble condition. A module trouble may occur for any of the following reasons:

•

Communication is lost with the FACP/Network Annunciator. All amber trouble LEDs will flash rapidly and the piezo will sound.
During this condition, an annunciator communication fault will be displayed at the control panel. (COMM LOSS)

Example: Trouble with the EIA-485 communication loop or incorrect address selection.

•

Annunciator points 33-64
All yellow LEDs will flash rapidly and the piezo will sound.

For AM2020/AFP1010 only: Annunciator points 33 - 64 are not programmed as type ID ACON and an SCE is not
connected or responding to the SCS. During this condition, an expander trouble will be displayed at the control panel.

NFS-320 or NFS2-640 with NCA-2: Annunciator points 33 - 64 are not programmed to an unused output point and the
SCE-8 is not connected. During this condition, an expander trouble will be displayed at the control panel.

8

Activates CON

ON⁄OP

CM

Deactivates CON

OFF⁄CL

CM

depends on CBE after Reset

Deactivates CON

ON⁄OP

CM

Activates CON

OFF⁄CL

CM

9

Activates CON

ON⁄OP

CM

Deactivates CON

OFF⁄CL

CM

depends on CBE after Reset

Deactivates CON

ON⁄OP

CM

Activates CON

OFF⁄CL

CM

SWITCH

GROUP TYPE

FSCS DEDICATED SYSTEM TOGGLE SWITCH POSITION

ON

AUTO

OFF

1-9

see above

depends on CBE after Reset (see

Automatic Control in Dedicated

System Operation section)

see above

Table 3.8 FSCS Toggle Switch Group LED Operation

SWITCH

GROUP TYPE

Green LED

turns ON when

Yellow LED

turns ON when

Amber LED

turns ON when

1

VER

OFF⁄CL

MM Deactivates

VER

ON⁄OP

MM Activates

see FSCS Trouble Conditions

2

VER

ON⁄OP

MM Activates

VER

ON⁄OP

MM Deactivates

see FSCS Trouble Conditions

3

VER

ON⁄OP

MM Activates

VER

ON⁄OP

MM Activates

see FSCS Trouble Conditions

4

VER

OFF⁄CL

MM Deactivates

VER

ON⁄OP

MM Activates

see FSCS Trouble Conditions

5

VER

ON⁄OP

MM Activates

VER

ON⁄OP

MM Deactivates

see FSCS Trouble Conditions

6

VER

ON⁄OP

MM Activates

VER

ON⁄OP

MM Activates

see FSCS Trouble Conditions

7

VER

OFF⁄CL

MM Deactivates

VER

ON⁄OP

MM Activates

see FSCS Trouble Conditions

8

VER

ON⁄OP

MM Activates

VER

ON⁄OP

MM Deactivates

see FSCS Trouble Conditions

9

VER

ON⁄OP

MM Activates

VER

ON⁄OP

MM Activates

see FSCS Trouble Conditions

Table 3.7 FSCS Toggle Switch Functions (Alarm Condition)

«
...
60
61
62
63
64
...
»

Содержание NOTIFIER SCS Series



















































































































































































































Отзывы:

Нет отзывов