Honeywell NOTIFIER SCS Series Скачать руководство пользователя страница 162 | Manualshive

Страница: 162 / 210

Honeywell NOTIFIER SCS Series Скачать руководство пользователя страница 162

162

SCS Series Manual —

P/N 15712:L 7/18/16

Ratings and Wiring Diagrams

HVAC Wiring Diagrams

Figure 5.53 Motorized Damper Control - HVAC Switch Group Type 2

Figure 5.53 depicts a motorized damper in an HVAC system with the capability of verification of the

OPEN

state, switch group type 2. In the

above configuration, the EMS is supplying power to the damper closed power line. When power is supplied to the damper closed power line,
the damper closes. When the damper completely closes, the damper closed limit switch is

CLOSED

, indicating that the damper is in the

CLOSED

position. The VER

ON⁄OP

MM monitors the

CLOSED

position of the damper open limit switch. In this case the VER

ON⁄OP

MM is deac-

tivated because the damper is

CLOSED

.

Power Source

Damper

Open

Power

ELR-47K

(use 3.9K listed ELR with FZM-1)

Power Return

D

M

O-

h2

a-

fs-

2

.w

m

f

SLC Loop

Damper
Closed
Power

AC

MOTOR

DAMPER

CLOSED

Energy

Management

System

FMM-1

VER

ON⁄OP

MM

(deactivated)

N/O

COM

Limit Switch

for open

position

*If the SLC device does
not match the one in
this figure, refer to the
SLC manual appendix,
which contains wiring
conversion charts for
type V and type H
modules.

«
...
160
161
162
163
164
...
»

Содержание NOTIFIER SCS Series



















































































































































































































Отзывы:

Нет отзывов