Honeywell NOTIFIER SCS Series Скачать руководство пользователя страница 128

Страница: 128 / 210

128

SCS Series Manual —

P/N 15712:L 7/18/16

Ratings and Wiring Diagrams

Non-dedicated Smoke Control System Wiring Diagrams

Figure 5.19 Fan Control, Non-dedicated System - FSCS Switch Group Type 4

Figure 5.19 depicts a fan in a non-dedicated system with the capability of

control and verification of the

OFF

state, switch group type 4. In

the above configuration, the CON

ON⁄OP

CM is deactivated. The CON

ON⁄OP

CM is wired in parallel with the EMS; when wired in parallel with

the EMS the CM must be a relay module. When the CON

ON⁄OP

CM is deactivated, the EMS is free to control the fan. In this case the EMS is

OFF

, so no power is being supplied to the fan. When no power is supplied to the fan, the fan is

OFF

and the sail switch is

CLOSED

, indicating

no airflow in the duct. The VER

OFF⁄CL

MM monitors the

CLOSED

position of the sail switch, which would indicate when the fan is

OFF

. In this

case the VER

OFF⁄CL

MM is activated because the fan is

OFF

due to the EMS. When the CON

ON⁄OP

CM is activated, the CON

ON⁄OP

CM over-

rides whatever state the EMS is in and closes the normally open contactor, thus supplying power to the fan and turning it on.

FRM-1

COM

N/O

Power Source

1a listed

contactor

Service

Disconnect

Switch

ELR-47K

(use 3.9K listed ELR with FZM-1)

Listed

Sail

Switch

N/O

COM

N/C

Power Return

Listed

24 VDC

Power Source

VER

OFF/CL

(activated)

nf4

-f

-2

SLC Loop

FAN OFF

Energy
Management
System

FMM-1

CON

ON/OP

(deactivated)

*If the SLC device
does not match the
one in this figure,
refer to the SLC
manual appendix,
which contains wiring
conversion charts for
type V and type H
modules.

Содержание NOTIFIER SCS Series



















































































































































































































Результаты поиска

Содержание NOTIFIER SCS Series

Отзывы:

Honeywell NOTIFIER SCS Series, Руководство по эксплуатации и установке, Страница: 128 / 210

Результаты поиска

Содержание NOTIFIER SCS Series

Отзывы: