Honeywell NOTIFIER SCS Series Скачать руководство пользователя страница 132 | Manualshive

Страница: 132 / 210

Honeywell NOTIFIER SCS Series Скачать руководство пользователя страница 132

132

SCS Series Manual —

P/N 15712:L 7/18/16

Ratings and Wiring Diagrams

Non-dedicated Smoke Control System Wiring Diagrams

5.4.2 Motorized Dampers

Figure 5.23 Motorized Damper Control

Non-dedicated System - FSCS Switch Group Type 1

Figure 5.23 depicts a motorized damper in a non-dedicated system with the capability of

CLOSED

control and verification of the

CLOSED

state, switch group type 1. In the above configuration, the CON

OFF⁄CL

CM is deactivated. The CON

OFF⁄CL

CM controls two contactors: a nor-

mally closed contactor for the damper open power line, and a dual normally open/normally closed contactor for the damper close power.
When the CON

OFF⁄CL

CM is activated, the normally closed contactor is opened (cutting any power supplied by the EMS to the damper open

power line), the normally closed portion of the dual contactor is opened (cutting any power supplied by the EMS to the damper closed power
line), and the normally open portion of the dual contactor is closed, thus supplying power to close the damper. When the CON

OFF⁄CL

CM is

deactivated, the EMS is free to control the damper. The EMS is currently supplying power to the damper closed power line.

When power is supplied to the damper closed power line, the damper closes. When the damper completely closes, the damper closed limit
switch is

CLOSED

, indicating that the damper is in the

CLOSED

position. The VER

OFF⁄CL

MM monitors the

CLOSED

position of the damper

closed limit switch. In this case the VER

OFF⁄CL

MM is activated because the damper is

CLOSED

.

Power Source

1a, 1b listed

contactor

Damper

Open

Power

ELR-47K

(use 3.9K listed ELR with FZM-1)

N/O

COM

Power Return

Listed

24 VDC

Power Source

FMM-1

DM

O-

nf

1a

-fs-

2

.w

m

f

1b listed

contactor

CON

OFF/CL

CM

(deactivated)

VER

OFF/CL

MM

(activated)

Limit Switch
for closed
position

Damper
Closed
Power

AC

MOTOR

DAMPER

CLOSED

FCM-1

Energy

Management

System

SLC Loop

*If the SLC device does
not match the one in
this figure, refer to the
SLC manual appendix,
which contains wiring
conversion charts for
type V and type H
modules.

«
...
130
131
132
133
134
...
»

Содержание NOTIFIER SCS Series



















































































































































































































Отзывы:

Нет отзывов