Honeywell NOTIFIER SCS Series Скачать руководство пользователя страница 130

Страница: 130 / 210

130

SCS Series Manual —

P/N 15712:L 7/18/16

Ratings and Wiring Diagrams

Non-dedicated Smoke Control System Wiring Diagrams

Figure 5.21 Fan Control, Non-dedicated System - FSCS Switch Group Type 7

Figure 5.21 depicts a fan in a non-dedicated system with the capability of

and

OFF

control and verification of the

OFF

state, switch group

type 7. In the above configuration, the CON

ON⁄OP

CM is deactivated and the CON

OFF⁄CL

CM is deactivated. These two control modules are

always in the opposite state when the smoke control system is in operation and are always deactivated during normal operation. The
CON

ON⁄OP

CM is wired in parallel with the EMS; when wired in parallel with the EMS the CM must be a relay module. When the

CON

ON⁄OP

CM and the CON

OFF⁄CL

CM are deactivated, the EMS is free to control the fan. In this case the EMS is

, so power is being sup-

plied to the fan. When power is supplied to the fan, the fan is

and the sail switch is

OPEN

, indicating airflow in the duct. The VER-

OFF⁄CL

MM monitors the

CLOSED

position of the sail switch, which would indicate when the fan is

OFF

. In this case the VER

OFF⁄CL

MM is

deactivated because the fan is

due to the EMS. When the CON

ON⁄OP

CM is activated for smoke control, the CON

ON⁄OP

CM overrides

whatever state the EMS is in and closes the normally open contactor, thus supplying power to the fan and turning it

. When the

CON

OFF⁄CL

CM is activated for smoke control, the CON

OFF⁄CL

CM opens the normally closed contactor and turns the fan

OFF

, overriding

whatever state the EMS is in.

Power Source

1a listed

contactor

Service

Disconnect

Switch

ELR-47K

(use 3.9K listed ELR with FZM-1)

Listed

Sail

Switch

N/O

COM

N/C

Power Return

Listed

24 VDC

Power Source

VER

OFF/CL

(deactivated)

n-n

f7-

-2

SLC Loop

FAN ON

Energy
Management
System

FMM-1

CON

ON/OP

(deactivated)

FRM-1

FCM-1

CON

OFF/CL

(deactivated)

Listed

24 VDC

Power Source

1b listed

contactor

*If the SLC device
does not match the
one in this figure,
refer to the SLC
manual appendix,
which contains
wiring conversion
charts for type V
and type H
modules.

Содержание NOTIFIER SCS Series



















































































































































































































Результаты поиска

Содержание NOTIFIER SCS Series

Отзывы:

Honeywell NOTIFIER SCS Series, Руководство по эксплуатации и установке, Страница: 130 / 210

Результаты поиска

Содержание NOTIFIER SCS Series

Отзывы: