Honeywell NOTIFIER SCS Series Скачать руководство пользователя страница 188

Страница: 188 / 210

188

SCS Series Manual —

P/N 15712:L 7/18/16

Ratings and Wiring Diagrams

HVAC Wiring Diagrams

Figure 5.80 EP Damper Control - HVAC Switch Group Type 14

Figure 5.80 depicts an EP damper in an HVAC system with the capability of

OPEN

and

CLOSED

control and verification of the

OPEN

state,

switch group type 14. In the above configuration, the CON

ON⁄OP

CM is activated and the CON

OFF⁄CL

CM is deactivated. The CON

ON⁄OP

controls a normally closed contactor for the pressure switch power line. When the CON

ON⁄OP

CM is activated, the normally closed contactor

is opened. When the contactor opens, power is cut from the pressure switch, which allows airflow to open the damper. When the
CON

ON⁄OP

CM is deactivated, the EMS is free to control the damper. The EMS is currently being overridden by the CON

ON⁄OP

CM.

When power is cut from the pressure switch, the damper opens. When the damper completely opens, the damper open limit switch is

CLOSED

, indicating that the damper is in the

OPEN

position. The VER

ON⁄OP

MM monitors the

CLOSED

position of the damper open limit

switch In this case the VER

ON⁄OP

MM is activated because the damper is

OPEN

FMM-1

Airflow

PRESSURE

SWITCH

SMOKE

DAMPER

OPEN

Power Source

Listed
24 VDC
Power Source

SLC Loop

FCM-1

CON

OFF/CL

(deactivated)

EP-

14A

-f

s-2

Power

Return

VER

ON⁄OP

(activated)

N/O

COM

Limit Switch

for open

position

ELR-47K

(use 3.9K listed ELR with FZM-1)

Pneumatic

Tubing

Energy
Management
System

1a listed

contactor

1b listed

contactor

FCM-1

CON

ON/OP

(activated)

*If the SLC device does
not match the one in
this figure, refer to the
SLC manual appendix,
which contains wiring
conversion charts for
type V and type H
modules.

Содержание NOTIFIER SCS Series



















































































































































































































Результаты поиска

Содержание NOTIFIER SCS Series

Отзывы:

Honeywell NOTIFIER SCS Series, Руководство по эксплуатации и установке, Страница: 188 / 210

Результаты поиска

Содержание NOTIFIER SCS Series

Отзывы: