manualshive.com logo in svg

Honeywell NOTIFIER SCS Series, Руководство по эксплуатации и установке, Страница: 66 / 210

Поделиться
Скачать
Honeywell NOTIFIER SCS Series Скачать руководство пользователя страница 66

66

SCS Series Manual —

 P/N 15712:L  7/18/16

The SCS⁄SCE

Configuration

SCS Dipswitch Settings for HVAC Mode

The tables on the pages that follow describe the dipswitch settings necessary to configure the SCS⁄SCE for many variations of heating, ven-
tilating and air conditioning control. The same dipswitch settings and switch group layouts apply when an SCS is used without an SCE. Each 
description of a dipswitch setting follows the format shown below: 

For instance, this particular dipswitch setting allows the SCS⁄SCE to function in the HVAC mode (dipswitch 6 in the OFF position). The set-
ting for switches 1-5 not only select the HVAC group types of 14 and 5 but configure the switch group layout as shown to the left, where 
switch groups 1, 2, 3, 4, 9, 10, 11, and 12 are set for group type 8 operation and switch groups 5, 6, 7, 8, 13, 14, 15, and 16 are set for group 
type 1. 

7

CON

OFF⁄CL

, VER

ON⁄OP

 and VER

OFF⁄CL

Turn a fan off (close a damper) and verify when the fan is on and off (damper 
open and closed)

8

CON

ON⁄OP

Turn a fan on (open a damper)

9

CON

ON⁄OP

 and VER

OFF⁄CL

 

Turn a fan on (open a damper) and verify when the fan is off (damper closed)

10

CON

ON⁄OP

 and VER

ON⁄OP

 

Turn a fan on (open a damper) and verify when the fan is on (damper open)

11

CON

ON⁄OP

, VER

ON⁄OP

 and VER

OFF⁄CL

Turn a fan on (open a damper) and verify when the fan is on and off (damper 
open and closed)

12

CON

ON⁄OP

, CON

OFF⁄CL

 

Turn a fan on and off (open and close a damper)

13

CON

ON⁄OP

, CON

OFF⁄CL

 and VER

OFF⁄CL

Turn a fan on and off (open and close a damper) and verify when the fan is off 
(damper closed)

14

CON

ON⁄OP

, CON

OFF⁄CL

 and VER

ON⁄OP

Turn a fan on and off (open and close a damper) and verify when the fan is on 
(damper open)

15

CON

ON⁄OP

, CON

OFF⁄CL

, VER

ON⁄OP

 and 

VER

OFF⁄CL

Turn a fan on and off (open and close a damper) and verify when the fan is on 
and off (damper open and closed)

Table 3.9  HVAC Mode Switch Group Types 

19 

When used with an SCE, eight switch groups are 
available for group type 14 operation and eight are 
available for group type 5 operation in the format 
shown to the left. Type 14 switch groups require 
control modules and monitor modules. Type 14 
switch groups are usually only used for fans. One 
control module is used for the ON control of the fan, 
the other control module is used for the OFF control. 
The monitor module is used for the ON verification of 
the fan. Type 5 switch groups require one control 
module and one monitor module. Type 5 switch 
groups can be used for fans or dampers. The control 
module is used for OFF control of a fan and the 
monitor module is used for the OFF verification of the 
fan.

14

5

14

5

14

5

14

5

14

5

14

5

14

5

14

5

SCS-8

SCE-8

OFF
ON

Switches 1-5 select 

the SCS⁄SCE for a 

particular configuration 

of switch group types

Switch 6, when in the 
OFF position, selects 

HVAC Mode.

See Table 3.4 for settings of 

switches 7 and 8.

Reference 

Number

This diagram depicts the layout of the switch 
groups and the group type associated with 
each switch group for the particular 
dipswitch setting on the right.

This text describes the functions, 

capabilities, and limitations of the 

SCS⁄SCE for the particular dipswitch 

setting.

This diagram depicts the dipswitch

setting necessary to configure the

SCS⁄SCE for the capabilities

mentioned to the left.

Содержание NOTIFIER SCS Series



















































































































































































































Отзывы:

Нет отзывов