Honeywell NOTIFIER SCS Series Скачать руководство пользователя страница 182

Страница: 182 / 210

182

SCS Series Manual —

P/N 15712:L 7/18/16

Ratings and Wiring Diagrams

HVAC Wiring Diagrams

Figure 5.74 EP Damper Control - HVAC Switch Group Type 8

Figure 5.74 depicts an EP damper in an HVAC system with the capability of

OPEN

control, switch group type 8. In the above configuration,

the CON

ON⁄OP

CM is activated. The CON

ON⁄OP

CM controls a normally closed contactor for the pressure switch power line. When the

CON

ON⁄OP

C M is activated, the normally closed contactor is opened. When the contactor opens, power is cut from the pressure switch,

which allows airflow to open the damper. When the CON

ON⁄OP

CM is deactivated, the EMS is free to control the damper. The EMS is cur-

rently being overridden by the CON

ON⁄OP

CM.

FMM-1

Airflow

PRESSURE

SWITCH

SMOKE

DAMPER

OPEN

Power

Source

Listed
24 VDC
Power Source

SLC Loop

P-h

A-

-2

Power

Return

VER

OFF⁄CL

(deactivated)

N/O

COM

Limit Switch
for closed
position

ELR-47K

(use 3.9K listed ELR with FZM-1)

Pneumatic

Tubing

Energy
Management
System

1b listed

contactor

FRM-1

CON

ON/OP

(activated)

COM

N/O.

*If the SLC device
does not match the
one in this figure,
refer to the SLC
manual appendix,
which contains
wiring conversion
charts for type V
and type H
modules.

Содержание NOTIFIER SCS Series



















































































































































































































Результаты поиска

Содержание NOTIFIER SCS Series

Отзывы:

Honeywell NOTIFIER SCS Series, Руководство по эксплуатации и установке, Страница: 182 / 210

Результаты поиска

Содержание NOTIFIER SCS Series

Отзывы: