manualshive.com logo in svg

Honeywell NOTIFIER SCS Series, Руководство по эксплуатации и установке, Страница: 86 / 210

Поделиться
Скачать
Honeywell NOTIFIER SCS Series Скачать руководство пользователя страница 86

86

SCS Series Manual —

 P/N 15712:L  7/18/16

The SCS⁄SCE

Programming

Example:
Switch group 1 for an SCS at address 1 would have protocol points 1-4 asso-
ciated with it. If the switch group was defined as switch group type 5, a con-
trol module would be mapped to point 1 and a monitor module would be 
mapped to point 3 with points 2 and 4 unneeded.

Optional Feature Programming for Control and 
Monitor Modules

In order for control and monitor modules to function properly in smoke con-
trol applications, certain optional features must be set. When programming Control Modules for smoke control applications, the Walk Test 
option must be disabled and the Signal Silence option must be enabled. This is accomplished by answering "NO" to the question "IS THE 
WALK TEST OPTION TO BE ENABLED FOR THIS DEVICE?" and answering "YES" to the question "IS THE SIGNAL SILENCE 
OPTION TO BE ENABLED FOR THIS DEVICE?" within partial point programming, as shown below, or full point programming, as 
shown in Section 2.4.4. When programming Monitor Modules for smoke control applications, the Tracking option must be enabled. This is 
accomplished by answering "YES" to the question "DO YOU WANT TO CHANGE THE TRACKING OPTION FOR THIS DEVICE?" 
within partial point programming, as shown below, or full point programming, as shown in Section 2.4.4.

Programming of the optional features for all modules can be accomplished through Partial Point Programming. After entering the program-
ming mode, select option 3, partial point programming, of the Main Programming Menu by pressing the following keys at the prompt: 

3 [

 

3=PPRG 

Option 3 from the Programming Menu allows the programmer to change the operational parameters of SLC Loop devices, software-defined 
zones, and EIA-485 protocol points.

After entering Partial System Programming, select option 4, Optional Features, by pressing the following keys at the prompt:

4 [

 

4=OPTNS 

Option 4 of the Partial Point Programming Menu allows the programmer to individually enable or disable, per device, the functions of Signal 
Silence and Walk Test (for control modules), Alarm Verification and Sensitivity (for addressable detectors), and Tracking (addressable detec-
tors and monitor modules). These functions must still be enabled or disabled, as appropriate, for the entire system (see Partial System Pro-
gramming). For an explanation of the functions of Signal Silence, Alarm Verification, Sensitivity, and Tracking, see the Glossary of Terms 
and Abbreviations at the end of this manual. 

A control module example: 

PRESS@1=TYPID,2=CBE,3=LBL,4=OPTNS,5=AMAP,6=CCBE@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@:@4
ENTER@LXX(D/M)YY,@ZXXX@OR@AXXPYY@FOR@PT.@CHANGE@(BCKSPC@TO@ABORT)@@@@@@@:@L3M21
DO@YOU@WANT@TO@CHANGE@THE@SIGNAL@SILENCE@OPTION@FOR@THIS@DEVICE?@(Y=YES,N=NO):@Y
IS@THE@SIGNAL@SILENCE@OPTION@TO@BE@ENABLED@FOR@THIS@DEVICE?@(Y=YES,N=NO)@@@@@:@Y
DO@YOU@WANT@TO@CHANGE@THE@WALK@TEST@OPTN@FOR@THIS@DEVICE?@(Y=YES,N=NO)@@@@@@@:@Y
IS@THE@WALK@TEST@OPTION@TO@BE@ENABLED@FOR@THIS@DEVICE?@(Y=YES,N=NO)@@@@@@@@@@:@N

A monitor module example:

PRESS@1=TYPID,2=CBE,3=LBL,4=OPTNS,5=AMAP,6=CCBE@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@:@4
ENTER@LXX(D/M)YY,@ZXXX@OR@AXXPYY@FOR@PT.@CHANGE@(BCKSPC@TO@ABORT)@@@@@@@:@L5M13
DO@YOU@WANT@TO@CHANGE@THE@TRACKING@OPTN@FOR@THIS@DEVICE?@(Y=YES,N=NO)@@@@@@@@:@Y
IS@THE@TRACKING@OPTION@TO@BE@ENABLED@FOR@THIS@DEVICE?@(Y=YES,N=NO)@@@@@@@@@@@:@Y

Full Point Programming

After entering the programming mode, select option 4, full point programming, of the Main Programming Menu by pressing the following 
keys at the prompt:

4 [

 

L3M64

A1P1

A1P4

L3M65

A1P2

A1P3

unneeded

unneeded

Содержание NOTIFIER SCS Series



















































































































































































































Отзывы:

Нет отзывов