manualshive.com logo in svg

Honeywell NOTIFIER SCS Series, Руководство по эксплуатации и установке, Страница: 85 / 210

Поделиться
Скачать
Honeywell NOTIFIER SCS Series Скачать руководство пользователя страница 85

SCS Series Manual —

 P/N 15712:L  7/18/16

85

Programming

The SCS⁄SCE

After selecting option 3 from the Main Programming menu, the display will show the Partial Point Programming submenu:

PRESS@1=TYPID,2=CBE,3=LBL,4=OPTNS,5=AMAP,6=CCBE@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@: 

After entering Partial System Programming, select option 2, Control-By-Event, by pressing the following keys at the prompt:

2 [

 

2=CBE 

Option 2 of the Partial Point Programming Menu allows the programmer to change the Control-By-Event (CBE) for any detector, module or 
software zone. The panel maintains a CBE for each device and zone installed in the system. 

When programming a particular device, the control panel prompts the programmer with:

ENTER@CONTROL-BY-EVENT@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@: 

The following display illustrates CBE programming for control module number 23 on SLC Loop 2 to activate software zones 15 and 29.

PRESS@1=TYPID,2=CBE,3=LBL,4=OPTNS,5=AMAP,6=CCBE@@@@@@@@@@@@@@@@@@@@@@@@@@@@:@2 
ENTER@LXX(D/M)YY,@ZXXX@OR@AXXPYY@FOR@PT.@CHANGE@(BCKSPC@TO@ABORT)@@@@@:@L2M23 
ENTER@CONTROL-BY-EVENT@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@: 
(Z15@Z29) 

For a complete description of the types, parameters, limitations, and guidelines of CBE programming, see Appendix A, Control-By-Event.

EIA-485 Protocol Point Mapping

Each control and monitor module associated with the FACP (being used for the purpose of smoke control or HVAC) must be properly and 
separately mapped to the specific protocol points of each toggle switch group within the SCS⁄SCE. This information must be programmed so 
that data going between the SCS⁄SCE and control/monitor modules can be properly routed through the FACP. 

Programming of point mapping for all modules can be accomplished through Partial Point Programming. After entering the programming 
mode, select option 3, partial point programming, of the Main Programming Menu by pressing the following keys at the prompt:

3 [

 

3=PPRG 

Option 3 from the Programming Menu allows the programmer to change the operational parameters of SLC Loop devices, software-defined 
zones, and EIA-485 protocol points.

After selecting option 3 from the Main Programming menu, the display will show the Partial Point Programming submenu:

PRESS@1=TYPID,2=CBE,3=LBL,4=OPTNS,5=AMAP,6=CCBE@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@: 

After entering Partial System Programming, select option 5, Annunciator Point Mapping, by pressing the following keys at the prompt:

5 [

 

5=AMAP 

Option 5 of the Partial Point Programming Menu allows the programmer to individually map devices or zones to EIA-485 protocol points for 
proper communication.

The following display illustrates mapping monitor module 11 on SLC Loop 1 to an SCS Module at address 1, Point 3.

PRESS@1=TYPID,2=CBE,3=LBL,4=OPTNS,5=AMAP,6=CCBE@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@:@5 
ENTER@LXX(D/M)YY,@ZXXX@OR@AXXPYY@FOR@PT.@CHANGE@(BCKSPC@TO@ABORT)@@@@@@@:@L1M11 
DO@YOU@WANT@TO@CHANGE@THE@ANNUNCIATOR@MAPPING@FOR@THIS@POINT?@(Y=YES,N=NO)@@@:@Y 
DO@YOU@WANT@THIS@POINT@MAPPED@TO@AN@ANNUNCIATOR?@(Y=YES,N=NO)@@@@@@@@@@@@@@@@:@Y 
ENTER@AXXPYY@FOR@ANNUNCIATOR@POINT@MAPPING@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@:@A1P3 

Each protocol point must be installed through Full Point Programming, as shown in Section 2.4.2, before a control or monitor module may 
be mapped to it. Every control and monitor module utilized for smoke control must be mapped to its associated protocol point within its 
respective switch group, as shown below.

NOTE:

A software zone is not a physical zone, but rather a software grouping in control panel memory.

Содержание NOTIFIER SCS Series



















































































































































































































Отзывы:

Нет отзывов