manualshive.com logo in svg

Honeywell NOTIFIER SCS Series, Руководство по эксплуатации и установке, Страница: 176 / 210

Поделиться
Скачать
Honeywell NOTIFIER SCS Series Скачать руководство пользователя страница 176

176

SCS Series Manual —

 P/N 15712:L  7/18/16

Ratings and Wiring Diagrams

HVAC Wiring Diagrams

5.5.3  EP Dampers 

Figure 5.67  EP Damper Monitor - HVAC Switch Group Type 1

Figure 5.67 depicts an EP damper in an HVAC system with the capability of verifying the 

CLOSED

 state, switch group type 1. In the above 

configuration, the EMS is supplying power to the pressure switch. When power is supplied, the pressure switch cuts the airflow to the 
damper, closing the damper. When the damper completely closes, the damper closed limit switch is 

CLOSED

, indicating that the damper is in 

the 

CLOSED

 position. The VER

OFF⁄CL

MM monitors the 

CLOSED

 position of the damper closed limit switch. In this case the VER

OFF⁄CL

MM is 

activated because the damper is 

CLOSED

.

Figure 5.68  EP Damper Monitor - HVAC Switch Group Type 2

FMM-1

Airflow

PRESSURE

SWITCH

SMOKE

DAMPER

CLOSED

Power Source

SLC Loop

De

p-

h1

-f

s

-2

.wmf

Power 

Return

VER

OFF⁄CL

MM

(activated)

N/O

COM

Limit Switch
for closed 
position

ELR-47K

(use 3.9K listed ELR with FZM-1)

Pneumatic

Tubing

Energy

Management

System

*If the SLC device 
does not match the 
one in this figure, 
refer to the SLC 
manual appendix, 
which contains wiring 
conversion charts for 
type V and type H 
modules.

Airflow

PRESSURE

SWITCH

SMOKE

DAMPER

CLOSED

Power Source

SLC Loop

De

p-

h2

-f

s

-2

.w

m

f

Power 

Return

ELR-47K

(use 3.9K listed ELR with FZM-1)

Pneumatic

Tubing

Energy

Management

System

N/O

COM

Limit Switch

for open 

position

VER

ON⁄OP

MM

(deactivated)

FMM-1

*If the SLC device 
does not match the 
one in this figure, 
refer to the SLC 
manual appendix, 
which contains 
wiring conversion 
charts for type V 
and type H modules.

Содержание NOTIFIER SCS Series



















































































































































































































Отзывы:

Нет отзывов