Honeywell NOTIFIER SCS Series Скачать руководство пользователя страница 108 | Manualshive

Страница: 108 / 210

Honeywell NOTIFIER SCS Series Скачать руководство пользователя страница 108

108

SCS Series Manual —

P/N 15712:L 7/18/16

Ratings and Wiring Diagrams

Air Flow Switches

5.2 Air Flow Switches

Any air flow switch used in a smoke control or HVAC system only requires UL listing for HVAC applications. Air flow verification may be
implemented either with an air flow switch or a pressure differential switch. The manufacturers listed below provide products that have been
identified for use with the SCS⁄SCE. The manufacturers, part numbers and device types are as follows:

5.3 Dedicated Smoke Control System Wiring Diagrams

5.3.1 Fans

Figure 5.1 Fan Control, Dedicated System - FSCS Switch Group Type 1

Figure 5.1 depicts a fan in a dedicated system with the capability of

OFF

control and verification of the

OFF

state, switch group type 1. In the

above configuration, the CON

OFF⁄CL

CM is deactivated. The CON

OFF⁄CL

CM controls a normally closed contact which switches power to the

fan (the contact is used when the power being switched is greater than 24 volts). When the CON

OFF⁄CL

CM is deactivated, the contact is

closed, thus supplying power to the fan. When power is supplied to the fan, the fan is

ON

and the sail switch is

OPEN

, indicating airflow in the

duct. The VER

OFF⁄CL

MM monitors the

CLOSED

position of the sail switch, which would indicate when the fan is

OFF

. In this case the VER-

OFF⁄CL

MM is deactivated because the fan is

ON

and the sail switch is

OPEN

.

Manufacturer

Model

Type

Johnson Controls

F62AA

Air Flow

Dayton

2E462

Pressure Differential

Antunes Controls

SMV, SMD, SML, JPD-2

Pressure Differential

Power Source

1a listed
contactor

Service
Disconnect
Switch

ELR-47K

(use 3.9K listed ELR with FZM-1)

N/O

COM

N/C

Power Return

Listed

24 VDC

Power

Source

FMM-1

FCM-1

CON

OFF/CL

CM

(deactivated)

VER

OFF/CL

MM

(deactivated)

FA

N

-Df1

-f

s

-2

.wmf

SLC Loop

FAN ON

Listed Sail
Switch

*If the SLC device
does not match the
one in this figure,
refer to the SLC
manual appendix,
which contains
wiring conversion
charts for type V
and type H
modules.

«
...
106
107
108
109
110
...
»

Содержание NOTIFIER SCS Series



















































































































































































































Отзывы:

Нет отзывов