Honeywell NOTIFIER SCS Series Скачать руководство пользователя страница 161 | Manualshive

Страница: 161 / 210

Honeywell NOTIFIER SCS Series Скачать руководство пользователя страница 161

SCS Series Manual —

P/N 15712:L 7/18/16

161

HVAC Wiring Diagrams

Ratings and Wiring Diagrams

5.5.2 Motorized Dampers

Figure 5.52 Motorized Damper Control - HVAC Switch Group Type 1

Figure 5.52 depicts a motorized damper in an HVAC system with the capability of verification of the

CLOSED

state, switch group type 1. In

the above configuration, the EMS is supplying power to the damper closed power line. When power is supplied to the damper closed power
line, the damper closes. When the damper completely closes, the damper closed limit switch is

CLOSED

, indicating that the damper is in the

CLOSED

position. The VER

OFF⁄CL

MM monitors the

CLOSED

position of the damper closed limit switch. In this case the VER

OFF⁄CL

MM is

activated because the damper is

CLOSED

.

Power Source

Damper

Open

Power

ELR-47K

(use 3.9K listed ELR with FZM-1)

N/O

COM

Power Return

FMM-1

fa

n-

h1

4-

fs

-2

.w

mf

SLC Loop

VER

OFF/CL

MM

(activated)

Limit Switch
for closed
position

Damper
Closed
Power

AC

MOTOR

DAMPER

CLOSED

Energy

Management

System

*If the SLC device
does not match the
one in this figure, refer
to the SLC manual
appendix, which
contains wiring
conversion charts for
type V and type H
modules.

«
...
159
160
161
162
163
...
»

Содержание NOTIFIER SCS Series



















































































































































































































Отзывы:

Нет отзывов