GE HEALTHCARE CARESCAPE Monitor B450 Скачать руководство пользователя страница 123

Страница: 123 / 236

Installation checkout

115

2062973-003

8.3.12 iPanel connection

Perform the following test only if the Citrix / iPanel is configured and in use.
1.

Select

Data & Pages > iPanel

and verify that the initial program (configured in Webmin) is

launched correctly.

Select

to exit the Citrix thin client.

8.3.13 Insite with EXC

Perform the following test only if remote service is configured and enabled, and you did not test
the connectivity already while you enabled it.
1.

Select

Configuration > Remote Service

In the

Sub-Modules for Remote Service

menu, select

Control

In the

Remote Service Control

window under

Test Connectivity

, select

Test

to test the

connectivity to the remote service server.

Verify that

Connection to Enterprise URL

and

Connection to Tunnel URL

both "Pass" the

test.

If one of the connection tests fail, check the failure description given and fix the connectivity
issue. Re-test the connectivity.

8.3.14 Test completion

Discharge Patient

Reset Case

to discard any changes made to the patient monitor

configuration during checkout.

•

Complete the Appendix

A. Installation check form

Содержание CARESCAPE Monitor B450













































































































































































































































Результаты поиска

Содержание CARESCAPE Monitor B450

Отзывы:

Похожие инструкции для CARESCAPE Monitor B450

Бренды по названию

Популярные бренды

GE HEALTHCARE CARESCAPE Monitor B450, Техническое руководство

Результаты поиска

Содержание CARESCAPE Monitor B450

Отзывы:

Похожие инструкции для CARESCAPE Monitor B450

Бренды по названию

Популярные бренды