manualshive.com logo in svg

GE HEALTHCARE CARESCAPE Monitor B450, Техническое руководство

Поделиться
Скачать
GE HEALTHCARE CARESCAPE Monitor B450 Скачать руководство пользователя страница 134

CARESCAPE Monitor B450

 126

2062973-003

9.4.2 Touchscreen sensor

The patient monitor has a resistive touchscreen sensor in the front of the LCD panel. The 
touchscreen sensor detects the presence and location of a touch within the display area and 
communicates the information through the touchscreen cable to the touchscreen controller 
at/ on the DC/DC board. 

9.4.3 E-Module board

The E-module board is a simple connector board. It interfaces the CPU Carrier Board to the 
DC/DC Board and provides a D25 male connector for one single-width E-module.

9.4.4 Alarm light board

The right hand side of the alarm light board contains red, yellow and blue LEDs to display 
different priority visual alarms. The left hand side of the alarm light board has blue LEDs for the 
silence alarm indicator light.
The alarm light board also has a separate light sensor that is capable of measuring the 
ambient light intensity. The ambient light feedback can be used to auto-adjust the brightness 
of the LED backlight of the LCD panel to the different ambient light conditions.
The alarm light board is connected to the DC/DC board with the alarm light cable.

9.4.5 Speaker Unit

The speaker unit is used to provide  audible alarms. The audio signal for the speaker is 
generated in the CPU carrier board using an audio codec and an audio amplifier. Audio 
feedback controls the operation of the speaker.
The speaker cable is connected to the E-module board.

9.4.6 Keypad & Buzzer

The patient monitor has a user interface board with an on/standby button and three power 
indicator LEDs: mains voltage indicator, battery use indicator and battery charging/failure 
indicator. The user interface board is connected to the DC/DC board with a user interface 
cable.
The buzzer is connected to the user interface board. It functions as a back-up speaker and also 
provides an audible power loss alarm.

9.4.7 Recorder unit/ assembly

The optional recorder assembly consists of a 50 mm recorder and a recorder board. 
The recorder board interfaces the recorder to the DC/DC board through the battery board. The 
recorder board provides the following main functions:
•

It passes the recorder control signals and the serial communication lines to the recorder.

•

It has a circuit-breaker and a LC-filter for the +12 V. 

•

It 5 V to the recorder. 

The serial communication and recorder buffers are in the EMBC section of the CPU carrier 
board.

9.4.8 Battery board

The battery board is a simple connector board. It interfaces the two lithium-ion batteries and 
the optional thermal recorder to the DC/DC board.

Содержание CARESCAPE Monitor B450













































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды