GE HEALTHCARE CARESCAPE Monitor B450 Скачать руководство пользователя страница 49

Страница: 49 / 236

Using Webmin service interface

2062973-003

NOTE: For more information on how to configure the IP address, refer to the PC’s
documentation.
5.

Launch a web browser on the service PC.

In the

Address

field, type

https:

[IX IP address]:10000

and press

Enter

NOTE:

[IX IP address]

is the IX Network IP address of the patient monitor.

The

Login to Webmin

dialog box displays.

Continue to

4.4. Login to Webmin

Closing Webmin

Restore the patient monitor’s original IX Network configuration and service PC’s network
settings if they were changed.

Disconnect the crossover cable from the patient monitor and from the service PC.

Reconnect the patient monitor back to the IX Network if applicable.

4.3

Remote access to Webmin using a service PC over the

IX Network

Connect a service PC to the IX Network using a standard network cable.

In patient monitor, select

Monitor Setup

Service

. The local browser opens and displays

the

Login to Webmin

dialog box.

Содержание CARESCAPE Monitor B450













































































































































































































































Результаты поиска

Содержание CARESCAPE Monitor B450

Отзывы:

Бренды по названию

Популярные бренды

GE HEALTHCARE CARESCAPE Monitor B450, Техническое руководство

Результаты поиска

Содержание CARESCAPE Monitor B450

Отзывы:

Бренды по названию

Популярные бренды