GE HEALTHCARE CARESCAPE Monitor B450 Скачать руководство пользователя страница 42 | Manualshive

Страница: 42 / 236

background image

CARESCAPE Monitor B450

34

2062973-003

3.7 User interface symbols

The following symbols appear in the software user interface

Alarm off indicator. Displays in the upper right corner of the parameter
window and in the Alarms Setup menu when physiological alarms for this
parameter are turned off.
The symbol is not displayed at the central station or on a remote bedside
monitor.

Alarm priority indicator: High (red). Indicates a high priority alarm.

Alarm priority indicator: Medium (yellow). Indicates a medium priority
alarm.

Alarm priority indicator: Low (cyan). Indicates a low priority alarm.

Alarm volume icon. Adjust the minimum alarm tone volume.

Audio alarms off indicator - Displays in the upper left corner of the alarm
area when physiological audible alarms are turned off.

Audio alarms paused indicator with countdown timer - Indicates all audio
alarms are paused and the amount of time remaining for the alarm pause
period displays as a countdown timer.
Displays in the upper left corner of the screen.

Pause audio alarms - Selectable from the monitor’s main menu. Also an
indicator of a temporarily paused active audio alarm.

Low priority audio off alarm indicator, Displays in the upper left corner of
the alarm area.

Only with software version 2 host build 2.0.7 or earlier:

Configuration warning. Displays when the priority setting for

HR/PR

high/low

, or

SpO2 low

has been set to low. Check the alarm

configuration. Displays in the upper left corner of the alarm area.

«
...
40
41
42
43
44
...
»

Содержание CARESCAPE Monitor B450













































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для CARESCAPE Monitor B450

Бренд: KaVo Страницы: 16

Бренд: ParaBody Страницы: 3

Бренд: Hach Страницы: 52

Бренд: hager Страницы: 2

Бренд: Yamaha Страницы: 139

Бренд: Yamaha Страницы: 19

Бренд: Yamaha Страницы: 32

Бренд: Phenix Technologies Страницы: 39

Бренд: Triton Страницы: 31

WELCH LVS 600 T

Бренд: Gardner Denver Страницы: 68

Бренд: Strapack Страницы: 16

Бренд: Hameg Страницы: 60

Бренд: Petromax Страницы: 16

LIGHT LINEAR PT 1

Бренд: LIGMAN Страницы: 6

Бренд: QRS Страницы: 12

Бренд: Ikan Страницы: 5

Бренд: probst Страницы: 112

Бренд: TECSYSTEM Страницы: 14

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды