GE HEALTHCARE CARESCAPE Monitor B450 Скачать руководство пользователя страница 67 | Manualshive

Страница: 67 / 236

background image

Hardware installation

59

2062973-003

B) Cable length is 5 to 15 meters

If complete isolation is not required, this method will provide the most cost effective means of
extending your USB installation. This type of installation should not be used for connections to
non-medically used rooms according to IEC 60601-1-1.
Displays may be extended up to 15 meters from the patient monitor using the following cables:

−

15-meter DVI-I to DVI-I video cable with DVI-I to DVI-D adapter (p/n 2042766-001).

−

5-meter USB extender (p/n 2042768-001).

−

Standard USB-A to USB-B cable, up to 5 meters.

In the following example, two 5-meter USB extenders, plus a standard 5-meter USB cable
extend the remote display up to 15 meters from the patient monitor.

USB-connection:
1.

Connect the Type A plug of the 1st USB extender to one of the downstream ports (Type A
USB port) on the back of the patient monitor.

2.

Connect the Type A plug of the 2nd USB extender to the Type A receptacle on the 1st USB
extender.

3.

Connect the Type A plug of the standard USB cable to the Type A receptacle on the 2nd
USB extender.

4.

Connect the Type B plug of the standard USB cable to the upstream port (Type B USB port)
on the bottom of the display.

Type A plug

Type A receptacle

USB extender

«
...
65
66
67
68
69
...
»

Содержание CARESCAPE Monitor B450













































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для CARESCAPE Monitor B450

Бренд: GE Страницы: 24

Бренд: NAD Страницы: 10

D-MAS HyperSat 2540

Бренд: DanMedical Страницы: 103

Бренд: made for movement Страницы: 51

Бренд: Cannon Страницы: 40

Бренд: NARGESA Страницы: 34

Sportsound SSR-200

Бренд: Daktronics Страницы: 5

Бренд: Xtool Страницы: 51

Бренд: H-TEC Education Страницы: 16

Бренд: H-TEC Education Страницы: 12

Бренд: IBEX Страницы: 4

Бренд: ParaBody Страницы: 3

Бренд: Valiani Страницы: 66

Бренд: Omlet Страницы: 2

Бренд: Omicron Страницы: 382

Бренд: Omicron Страницы: 188

Бренд: ValueStore US Страницы: 2

Бренд: Vibration Research Corporation Страницы: 333

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды