GE HEALTHCARE CARESCAPE Monitor B450 Скачать руководство пользователя страница 129

Страница: 129 / 236

Theory of operation

121

2062973-003

9.2.3 User Interface Controller (UIC) subsystem

The User Interface Controller (UIC) subsystem manages the following user interface related
functions.

Alarm light control

•

PUIC controller controls the alarm light LEDs according to the information received from
the CPU assembly.

•

The DC/DC board passes the +3.3V and +5 V supply voltages to the alarm light board.

Ambient light sensor

•

The PUIC controller digitizes the information received from the ambient light sensor and
passes it to the CPU assembly.

•

CPU assembly adjusts the brightness of the display according to the ambient light
information received from the PUIC controller.

User interface board

•

The UIC subsystem has the LED drives for three power indicator LEDs and ON/Stdby
button LED in the keypad.

•

The PUIC controller provides an audible power failure alarm to the buzzer in case of
sudden system power loss.

•

The On/Stdby button press and remote-on signal are read by the PUIC controller.

Touchscreen controller

•

The touchscreen controller digitizes the user input received from the touchscreen sensor
and passes the coordinate information to the CPU assembly using USB communication.

Содержание CARESCAPE Monitor B450













































































































































































































































Результаты поиска

Содержание CARESCAPE Monitor B450

Отзывы:

Похожие инструкции для CARESCAPE Monitor B450

Бренды по названию

Популярные бренды

GE HEALTHCARE CARESCAPE Monitor B450, Техническое руководство

Результаты поиска

Содержание CARESCAPE Monitor B450

Отзывы:

Похожие инструкции для CARESCAPE Monitor B450

Бренды по названию

Популярные бренды