manualshive.com logo in svg

GE HEALTHCARE CARESCAPE Monitor B450, Техническое руководство

Поделиться
Скачать
GE HEALTHCARE CARESCAPE Monitor B450 Скачать руководство пользователя страница 119

 Installation checkout

  111

2062973-003

monitor batteries and disconnecting the power cord from the wall outlet for a moment before 
turning the monitor on.
Verify that the patient monitor starts up normally:

−

The yellow, red and blue alarm lights are lit momentarily.

−

The speaker gives an audible beep.

−

The normal monitoring screen appears and there are no error messages on the 
screen.

NOTE: Refer to section 

11. Troubleshooting

 to see the procedure for battery conditioning and 

battery replacement, if you receive a 

Condition Battery A or Condition Battery B

 or a 

Battery 

A failure or Battery B failure

 message.

NOTE: Before taking the patient monitor into use for the first time, the battery should be fully 
charged. Keep the monitor connected to the mains until the battery is fully charged. 

8.3.2 Display

Picture quality 

Perform this test both for the integrated main display and for the optional secondary display.
1.

Verify that all text is readable and all images are clear.

2.

Verify that the brightness is good. Adjust if necessary.

Touchscreen control

Perform this test both for the integrated main display and for the optional secondary display.
1.

Verify the operation and the calibration of a touchscreen by touching a corner of an 
active parameter window. Verify that the selected menu is opened.

2.

Select

 

 

to close any open menu and return to the main display.

8.3.3 Device Information 

1.

Log in to Webmin.

2.

Select 

Information >

 

Device Information

.

3.

Verify that the device information is correct:

−

The connected parameter modules are identified.

−

The connected CARESCAPE Network ID interfaces are identified.

−

The connected USB input devices are identified.

4.

Stay connected to Webmin.

8.3.4 Configuration Information

1.

Select 

Information >

 

Configuration Information

.

2.

Verify that the patient monitor is correctly configured:

−

The host Information is correct.

−

The active software package is correct.

−

The correct host licenses are enabled.

−

The correct PDM licenses are enabled.

−

Patient ID prefix is correctly configured.

−

Unit and Bed name are correctly configured.

Содержание CARESCAPE Monitor B450













































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды