GE HEALTHCARE CARESCAPE Monitor B450 Скачать руководство пользователя страница 58 | Manualshive

Страница: 58 / 236

background image

CARESCAPE Monitor B450

50

2062973-003

WARNING

The use of accessories, transducers and cables other than those specified
may result in increased emissions or decreased immunity performance of

the equipment or system.

WARNING

For detailed instructions and information regarding supplies and

accessories, always refer to their own instructions for use.

5.3 Network infrastructure

Ensure that the applicable network infrastructure is in place prior to the installation of the
patient monitor.
Acquire the network configuration information from the hospital IT or the related project
documentation and installation files.

5.3.1 MC Network

•

The MC Network infrastructure shall be installed according to the CARESCAPE Network
Configuration Guide.

•

The installation site of the patient monitor shall have a wall jack and a network patch
cable for the MC Network.

•

Refer to the sections

7.2.2. Selecting and configuring CARESCAPE Network

unit and bed name

to see the configuration information you need to have available to

configure the patient monitor to the MC Network.

5.3.2 Wireless MC Network

•

The wireless MC Network infrastructure shall be installed according to the CARESCAPE
Wireless Network Configuration Guide.

•

Ensure that the wireless coverage area is adequate for the installation.

•

Refer to the sections

7.2.2. Selecting and configuring CARESCAPE Network

Configuring WLAN

7.4. Setting unit and bed name

to see the configuration

information you need to have available to configure the patient monitor to the wireless
MC Network.

5.3.3 S/5 Network

•

The S/5 Network shall be installed according to the S/5 Network Installation Guide. Refer
to the iCentral and iCentral Client Service Manual for iCentral installation instructions.

•

The installation site of the patient monitor shall have a wall jack and a network patch
cable for the S/5 Network.

•

Refer to the section

7.2.3. Selecting and configuring S/5 Network

to see the configuration

information you need to have available to configure the patient monitor to the wired S/5
Network.

5.3.4 S/5 Wireless Network

•

The S/5 Wireless Network shall be installed according to the S/5 Network Installation
Guide. Refer to the iCentral and iCentral Client Service Manual for iCentral installation
instructions.

•

Ensure that the wireless coverage area is adequate for the installation.

«
...
56
57
58
59
60
...
»

Содержание CARESCAPE Monitor B450













































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для CARESCAPE Monitor B450

Бренд: Raymarine Страницы: 464

Бренд: 3M Страницы: 8

Бренд: ZOLL Страницы: 3

Бренд: Jacobs Ladder Страницы: 16

Бренд: Tascam Страницы: 128

Бренд: ParaBody Страницы: 6

Бренд: Xo Страницы: 59

Бренд: Falcon Страницы: 8

Бренд: lancer Страницы: 3

Бренд: lancer Страницы: 12

Бренд: R2 Страницы: 26

Бренд: OAKWORKS Страницы: 2

Бренд: Oakton Страницы: 2

Бренд: Oakton Страницы: 2

Бренд: O2matic Страницы: 4

Бренд: MAGSTIM Страницы: 86

Бренд: KUHN Страницы: 112

Бренд: Federal Signal Corporation Страницы: 31

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды