GE HEALTHCARE CARESCAPE Monitor B450 Скачать руководство пользователя страница 164

Страница: 164 / 236

CARESCAPE Monitor B450

156

2062973-003

External alarm
light disconnect.
Check USB
connection.

1. The USB cable between the
patient monitor and the
secondary display is
disconnected when the
patient is admitted.

1. Reconnect the USB cable.

2. Secondary display turned to
standby when the patient is
admitted.

2. Turn on the secondary display.

NOTE: Select

Audio Pause

to acknowledge the message, if the USB

cable is disconnected or the secondary display turned off on purpose.

3. User interface board
communication failure.

3. Update PUIC (Power Management
and User Interface Controller) software
(host software) or replace user
interface board.

Power
management
failure

Power Management
Controller (communication)
failure.

Update PUIC software (host software)
or replace the DC/DC board.

Setting

activation after
next case end./

Setting

activation after
next discharge.

Service user has initiated a
delayed settings activation
that will automatically take
place after next case end. /
next discharge.

If required, the service user may cancel
the delayed setting activation. See
section

7.17.4. Canceling pending

settings activation

Software

activation after
next case end./

Software

activation after
next discharge.

Service user has initiated a
delayed software activation
that will automatically take
place after next case end /
next discharge.

If required, the service user may cancel
the delayed setting activation. See
section

7.19.3. Canceling pending host

software activation

Service Monitor
Activation Failed

Software activation failed.

Reactivate software. If that does not
help, reinstall the software and then
reactivate it.

Setting activation failed.

Reactivate settings.

Module

voltage low

•

One of the supply voltages
for the acquisition
modules is out of
specification.

•

An analog output voltage
is out of specification.

Diagnostics > Hardware Stats

diagnose the problem. If there is a
faulty board, replace it.

Application

error:

Webmin

The operating system informs
that the Webmin local
browser was terminated
abnormally.

Select

Audio Pause

to acknowledge

the message.

Message

Possible causes

Possible solutions

Содержание CARESCAPE Monitor B450













































































































































































































































Результаты поиска

Содержание CARESCAPE Monitor B450

Отзывы:

Бренды по названию

Популярные бренды

GE HEALTHCARE CARESCAPE Monitor B450, Техническое руководство

Результаты поиска

Содержание CARESCAPE Monitor B450

Отзывы:

Бренды по названию

Популярные бренды