GE HEALTHCARE CARESCAPE Monitor B450 Скачать руководство пользователя страница 44

Страница: 44 / 236

CARESCAPE Monitor B450

2062973-003

Monitor battery is full.

Monitor battery (green). The higher the charge, the bigger the green bar
within the symbol. Numbers indicate the remaining run time.

Monitor battery (yellow). This symbol and a message indicating low
battery charge appear when there is less than 20 minutes of run time left.

Monitor battery (red). This symbol and a message indicating empty
battery appear when there is less than 5 minutes of run time left.

Monitor battery is charging. There is a white running bar inside the
symbol.

Monitor battery failure indicator. Indicates a missing battery or a battery
failure.

PDM battery charging indicator. Indicates that the PDM battery is
charging.

PDM battery gauge indicator. Indicates the charge level of the battery.

PDM battery failure indicator. Indicates the battery is not available for use.

Snapshot indicator. Indicates the event has an associated snapshot.

Beat volume icon. Adjust the volume of the QRS beep tone. Also the beat
source indicator. Displays next to the selected beat source.

The following symbols appear in the software user interface

Содержание CARESCAPE Monitor B450













































































































































































































































Результаты поиска

Содержание CARESCAPE Monitor B450

Отзывы:

Похожие инструкции для CARESCAPE Monitor B450

Бренды по названию

Популярные бренды

GE HEALTHCARE CARESCAPE Monitor B450, Техническое руководство

Результаты поиска

Содержание CARESCAPE Monitor B450

Отзывы:

Похожие инструкции для CARESCAPE Monitor B450

Бренды по названию

Популярные бренды