manualshive.com logo in svg

GE HEALTHCARE CARESCAPE Monitor B450, Техническое руководство

Поделиться
Скачать
GE HEALTHCARE CARESCAPE Monitor B450 Скачать руководство пользователя страница 153

 Troubleshooting

  145

2062973-003

11.3.2 Ping a TCP/IP network device

Use this Webmin feature to verify connectivity with a network device on the MC Network and IX 
Network.

System power (mW)

System power is the total power consumption of the patient 
monitor. 

Power consumption is measured from the DC/DC 

board.

DC/DC temperature (°C)

The internal temperature of the patient monitor 
measured by the temperature sensor in the DC/DC board.

CPU Carrier Board

Measurement

Description

+ 12 Vsync CPU Voltage (in mV)

 

- 12 Vsync CPU Voltage (in mV)

These voltages are generated for the ECG and Invasive 
pressure analog outputs and marker-out synchronization 
pulse. The voltages are measured by the A/D converter in 
the CPU Carrier board.

+15V MOD voltage (mV)

This voltage is generated by the voltage converter in the 
DC/DC board. It supplies power to the E-module. The 
voltages are measured by the A/D converter in the CPU 
carrier board.

VSYS (mV)

This voltage is generated by the voltage converter in the 
DC/DC board. It is measured by the A/D converter in the 
CPU carrier board.

VSYS_EPORT (mV)

The VSYS_EPORT voltage is supplied for a PDM module 
that is connected to the ePort connector DB9) in the rear of 
the patient monitor. It is measured by the A/D converter in 
the CPU carrier board. The value is shown as “--” if PDM 
module is not connected, or if VSYS_PDM voltage is 
enabled.

VSYS_PDM (mV)

The VSYS_PDM voltage is supplied for a PDM module that 
is connected to the PDM connector in the module rail unit. 
It is measured by the A/D converter in the CPU carrier 
board. The value is shown as “--” if PDM module is not 
connected, or if VSYS_EPORT voltage is enabled.

CPU carrier temperature (°C)

The internal temperature of the patient monitor measured 
by the temperature sensor in the CPU carrier board.

CPU Module

Measurement

Description

CPU module temperature (°C)

The internal temperature of the patient monitor measured 
by the temperature sensor in the CPU module.

DC/DC Board

Measurement

Description

Содержание CARESCAPE Monitor B450













































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды