GE HEALTHCARE CARESCAPE Monitor B450 Скачать руководство пользователя страница 183

Страница: 183 / 236

Disassembly and reassembly

175

2062973-003

WARNING

ELECTRIC SHOCK - Always unplug the grounded cables when not in use.
Leaving them connected could result in an electric shock from the ground

contact in the other end.

Turn the patient monitor off from the

On/standby

button.

Disconnect the patient monitor power cord first from the wall outlet and then from the
monitor.

Remove the patient monitor batteries.

Disconnect all external cables connected to the patient monitor.

Disconnect all parameter modules.

Detach the patient monitor from the mount if installed.

NOTE: If you disconnect the patient monitor from the AC power source and remove the battery
prior to turning the monitor off, the monitor will start alarming about power loss situation.
Select the

Silence alarm

to silence this alarm.

Содержание CARESCAPE Monitor B450













































































































































































































































Результаты поиска

Содержание CARESCAPE Monitor B450

Отзывы:

Похожие инструкции для CARESCAPE Monitor B450

Бренды по названию

Популярные бренды

GE HEALTHCARE CARESCAPE Monitor B450, Техническое руководство

Результаты поиска

Содержание CARESCAPE Monitor B450

Отзывы:

Похожие инструкции для CARESCAPE Monitor B450

Бренды по названию

Популярные бренды