manualshive.com logo in svg

GE HEALTHCARE CARESCAPE Monitor B450, Техническое руководство

Поделиться
Скачать
GE HEALTHCARE CARESCAPE Monitor B450 Скачать руководство пользователя страница 145

 Maintenance and checkout

  137

2062973-003

10.4.5 Conditioning a battery

Condition the battery when a 

Condition Battery A 

or 

Condition Battery B

 message is shown 

on the monitor screen. The condition cycle recalibrates the electronic fuel gauge.
Condition the battery by fully discharging and recharging the battery twice according to the 
following procedure:
NOTE: The patient monitor must be in a discharged state during battery conditioning. 
Disconnect any acquisition modules from the patient monitor if connected.
1.

Turn on the patient monitor. Disconnect the power cord from the wall outlet. Leave the 
patient monitor on until the battery is fully discharged and the patient monitor turns off 
automatically. 

NOTE: Ignore the 

Monitor Battery Low

 and 

Monitor Battery Empty!

 messages when 

discharging the battery.
2.

Reconnect the power cord to the wall outlet and turn on the patient monitor. Leave the 
patient monitor on until the battery is fully recharged and the orange battery charging 
indicator LED turns off.

3.

Repeat the steps 1 and 2 once.

The battery is now conditioned and ready for use. However if either 

Condition Battery A 

or 

Condition Battery B 

message is still shown on the patient monitor screen, repeat the 

conditioning cycle once more. If the problem persists, replace the battery.
NOTE: Refer to section 

11.6. Battery diagnostics

 and 

11.7. Error messages and codes

 for more 

detailed information about the battery status and operating condition.

10.4.6 Replacing a battery

Replace the battery in the following situations:

−

if either 

Replace battery A

 or 

Replace battery B

 message is displayed. This message 

indicates that the full-charge capacity of the used battery has considerably degraded 
compared to the design capacity of a new battery.

−

if either 

Battery A failure

 or 

Battery B failure

 message is displayed.

Remove the battery from the patient monitor and install a new battery according to the battery 
installation instructions in the Hardware Installation section
NOTE: Refer to the section 

11.6. Battery diagnostics

 and 

11.7. Error messages and codes

 for 

more detailed information about the battery status and operating condition.
NOTE: Refer to the Troubleshooting chapter for more detailed information about the battery 
diagnostics and error messages.

WARNING

Do not incinerate a battery or store at high temperatures. Serious injury or 
death could result.

10.4.7 Battery recycling

This product contains Lithium-Ion batteries. At the end of their service life, 
batteries in this product must be recycled or disposed in accordance with local 
or national regulations. Do not dispose of batteries as trash or unsorted 
municipal waste. Requirements and services for recycling of batteries vary 
between countries.

Содержание CARESCAPE Monitor B450













































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды