manualshive.com logo in svg

GE HEALTHCARE CARESCAPE Monitor B450, Техническое руководство

Прибор мониторинга GE HEALTHCARE CARESCAPE Monitor B450, предназначен для наблюдения за пациентами в медицинских учреждениях. Техническое руководство доступно для бесплатного скачивания на нашем сайте. Узнайте больше о продукте и загрузите руководство на manualshive.com.

Поделиться
Скачать
background image

Table of contents

                                                             i

2062973-003

Table of contents

1

About this manual

1

1.1

Intended use of the manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  1

1.2

Intended audience of the manual. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  1

1.3

Conventions used in this manual  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  1
1.3.1 Product naming conventions  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  2

1.4

Illustrations and names . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  2

1.5

Ordering manuals. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  2

1.6

Related documents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  2

1.7

Trademarks  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  3
1.7.1 Third party trademarks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  3

1.8

Responsibility of the manufacturer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  3

1.9

Product availability. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  3

2

Safety information

5

2.1

General safety statements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  5

2.2

Safety message signal words. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  5

2.3

Safety symbols  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  6

3

System overview

9

3.1

System introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  9

3.2

System components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  9
3.2.1 Monitor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  9
3.2.2 Software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
3.2.3 Input devices. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
3.2.4 Acquisition modules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
3.2.5 CARESCAPE Network MC or S/5 Network. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
3.2.6 CARESCAPE Network IX . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
3.2.7 Unity Network ID connectivity device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
3.2.8 Secondary display. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
3.2.9 Printers and recorders . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
3.2.10  Service Interface. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

3.3

Controls and connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
3.3.1 Front view  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
3.3.2 Side views  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
3.3.3 Rear views . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

3.4

Service information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
3.4.1 Service requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
3.4.2 Equipment identification. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

3.5

Product security . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
3.5.1 Security features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
3.5.2 Security operations. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
3.5.3 Product change management . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
3.5.4 Communication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

3.6

Equipment symbols . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

Содержание CARESCAPE Monitor B450













































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для CARESCAPE Monitor B450

CAMAG ADC 2 Manual preview
ADC 2
Бренд: CAMAG Страницы: 40
Warehouse-lighting LTR Series Installation Instructions preview
LTR Series
Бренд: Warehouse-lighting Страницы: 3
Eagle Group SHT Series Operation Manual preview
SHT Series
Бренд: Eagle Group Страницы: 8
E2S A112N Installation Instructions preview
A112N
Бренд: E2S Страницы: 5
iHealth PO3M Quick Start Manual preview
PO3M
Бренд: iHealth Страницы: 8
Nautilus 9NP-B7524 Series Owner'S Instructions preview
9NP-B7524 Series
Бренд: Nautilus Страницы: 2
Nautilus Be strong NS 700X Owner'S Manual preview
Be strong NS 700X
Бренд: Nautilus Страницы: 34
Nautilus BE STRONG E916 Quick Start Manual preview
BE STRONG E916
Бренд: Nautilus Страницы: 21
Nellcor Oximax NPB-40 Operator'S Manual preview
Oximax NPB-40
Бренд: Nellcor Страницы: 161
Nellcor OXIMAX N-600X Series Service Manual preview
OXIMAX N-600X Series
Бренд: Nellcor Страницы: 210
OAKWORKS PT series Instruction Manual preview
PT series
Бренд: OAKWORKS Страницы: 24
Raytec VARIO2 series Full Installation And Setup Manual preview
VARIO2 series
Бренд: Raytec Страницы: 60
Waterpik WP-800 Series Quick Start Manual preview
WP-800 Series
Бренд: Waterpik Страницы: 2
JBM 52489 Instruction Manual preview
52489
Бренд: JBM Страницы: 12
TANNER Scientific Cryostat TN60 Operating Instructions Manual preview
Cryostat TN60
Бренд: TANNER Scientific Страницы: 44
MMF POS 2261998USBA1-XX Instruction Manual & User Manual preview
2261998USBA1-XX
Бренд: MMF POS Страницы: 5
KaVo INTRAmatic 31 ES Instructions For Use Manual preview
INTRAmatic 31 ES
Бренд: KaVo Страницы: 52
KaVo INTRA PROPHYwiz 181 P Instructions For Use Manual preview
INTRA PROPHYwiz 181 P
Бренд: KaVo Страницы: 22

Бренды по названию

Популярные бренды

Загрузить еще бренды