GE HEALTHCARE CARESCAPE Monitor B450 Скачать руководство пользователя страница 23 | Manualshive

Страница: 23 / 236

background image

System overview

15

2062973-003

Refer to the patient monitor’s supplemental information manual for a list of compatible
displays.

3.2.9 Printers and recorders

The patient monitor can print to a recorder and to a laser printer.
Refer to the patient monitor’s supplemental information manual for a list of compatible
recorders and laser printers.

Laser printers

A laser printer can print for example waveforms, graphic and numeric trends, snapshots,
events history, parameter specific printouts, stored laboratory data and calculation results and
care reports. Refer to the patient monitor’s user’s manual for more information about printing.
The patient monitor supports printing:
•

to a laser printer that is connected to the patient monitor via the IX Network or directly to
the IX connector in the patient monitor.

•

to a laser printer that is connected to a CIC Pro Clinical Information Center on the MC
Network.

•

to a laser printer that is connected to an iCentral on the S/5 Network.

Recorders

A recorder may print text, waveforms and numeric trends.
The patient monitor supports printing:
•

to an integrated, local recorder (optional).

•

to a PRN 50M recorder connected to another patient monitor, or to a CIC Pro Clinical
Information Center, on the MC Network.

«
...
21
22
23
24
25
...
»

Содержание CARESCAPE Monitor B450













































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для CARESCAPE Monitor B450

Бренд: Qingdao H.Y Страницы: 6

Бренд: Fein Страницы: 248

Бренд: ZF Страницы: 30

Бренд: Raymarine Страницы: 111

Бренд: MacDon Страницы: 89

Бренд: Yates Страницы: 2

Бренд: JAC Страницы: 100

Бренд: lancer Страницы: 12

medialon Showmaster Go

Бренд: 7th Sense Страницы: 9

Бренд: YYZ Lighting Страницы: 3

Бренд: Camp Safety Страницы: 118

Бренд: Ultrafast Systems Страницы: 39

Бренд: Mackworth Страницы: 2

Бренд: Taylor Страницы: 41

Бренд: Rational Страницы: 60

Бренд: TANACOM Страницы: 27

Бренд: iBACheck Страницы: 2

Бренд: Tanaka Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды