GE HEALTHCARE CARESCAPE Monitor B450 Скачать руководство пользователя страница 71

Страница: 71 / 236

Hardware installation

2062973-003

6.6 Connecting to the MC Network or the S/5 Network

WARNING

MISSED ALARMS - Do not use with iCentral software with Versions 5.0.3 and

earlier or with Mobile Care Server with Version 5.2 and earlier.

WARNING

INCORRECT CALCULATIONS - Using the System with the Aware Gateway

software version 1.4 or earlier could result in incorrect patient height and
weight information. This could lead to incorrect drug dose calculations,

hemodynamic calculations, or oxygenation calculations. Prior to installing

the System, please contact the GE Healthcare Aware Gateway HL7
Integration Engineering Team or your GE Healthcare service representative

to verify or update your Aware Gateway configuration.

WARNING

EXCESSIVE LEAKAGE CURRENT - Only devices that are specified compliant

with IEC 60950-1 or IEC 60601-1 may be connected to the Ethernet MC or IX
ports.

The patient monitor can be connected either to the wired MC Network or S/5 Network.
•

Connect the MC Network or the S/5 Network patch cable to the network connector
labelled as “MC” in the rear panel of the patient monitor.

6.7 Connecting to the IX Network

•

Connect the IX Network patch cable to the network connector labelled as “IX” in the rear
panel of the patient monitor.

6.8 Connecting to a Unity Network ID connectivity device

Ensure that the Unity Network ID connectivity device is properly mounted, installed and
configured prior to connecting it to the patient monitor.

Содержание CARESCAPE Monitor B450













































































































































































































































Результаты поиска

Содержание CARESCAPE Monitor B450

Отзывы:

Бренды по названию

Популярные бренды

GE HEALTHCARE CARESCAPE Monitor B450, Техническое руководство

Результаты поиска

Содержание CARESCAPE Monitor B450

Отзывы:

Бренды по названию

Популярные бренды