GE HEALTHCARE CARESCAPE Monitor B450 Скачать руководство пользователя страница 169

Страница: 169 / 236

Troubleshooting

161

2062973-003

On/standby button and alarm light issues

Alphanumeric Keyboard and barcode scanner issues

Speaker / audible alarm issues

Problem

Possible cause

Recommended action

On/Standby and the power
indicator LEDs are inoperative.

User interface cable is loose or
faulty.

Check user interface cable and replace it,
if necessary

User interface board is faulty.

Replace the user interface board.

Alarm light does not illuminate
when there is an alarm
condition on (audible alarms
work and alarm message is
visible)

Alarm light cable is loose.

Connect the alarm light cable to the DC/
DC board.

Alarm light board or alarm light
cable is faulty.

Replace the alarm light board

Alarm light does not illuminate
during power-on self test.

“Warm start”

It is less than 15 minutes since the last
power-up (warm start) and this normal
operation.
The alarm light illuminates during the
power-on self test only if it is a cold start
(more than 15 minutes from the previous
start-up).

Problem

Possible cause

Recommended action

Wrong character is displayed
when a key is pressed on
keyboard.

The keyboard locale is not
configured correctly.

Configure the keyboard locale correctly,
see

“7.10”

Wrong character is displayed
when a barcode is read.

The keyboard locale is not
configured correctly.

Configure the keyboard locale correctly,
see

“7.10”

The barcode reader’s language
configuration is incorrect.

Refer to the barcode reader manual.

Barcode reader does not read a
multi-field barcode correctly.
(i.e., the information is not
populated correctly to the fields
in the Admit menu).

Barcode reader parser
configuration is incorrect.

Configure the barcode settings, see

“7.8.2”

The barcode reader is
incompatible with the parser
configuration (field lengths, field
types, delimeters, symbologies
etc.).

Check the barcode information content
and compare it to the current parser
configuration.

Problem

Possible cause

Recommended action

Содержание CARESCAPE Monitor B450













































































































































































































































Результаты поиска

Содержание CARESCAPE Monitor B450

Отзывы:

Похожие инструкции для CARESCAPE Monitor B450

Бренды по названию

Популярные бренды

GE HEALTHCARE CARESCAPE Monitor B450, Техническое руководство

Результаты поиска

Содержание CARESCAPE Monitor B450

Отзывы:

Похожие инструкции для CARESCAPE Monitor B450

Бренды по названию

Популярные бренды