GE HEALTHCARE CARESCAPE Monitor B450 Скачать руководство пользователя страница 113 | Manualshive

Страница: 113 / 236

background image

Installation checkout

105

2062973-003

9.

Read and record the current leakage indicated on the safety tester.

10. Power off the device under test.

Acceptance criteria in Normal Condition (NC):
•

All readings shall be less than or equal to 300

μ

A f

or installations that require compliance

to UL 60601-1 requirements.

•

All readings shall be less than or equal to 500

μ

A f

or installations that require compliance

to EN 60601-1 / IEC 60601-1 requirements.

Acceptance criteria in Single Fault Condition (SFC) – one of the supply conductors open at a
time:
•

All readings shall be less than or equal to 1 mA.

8.2.6 Enclosure leakage current (touch current) test

This test measures current leakage through the exposed conductive parts on the device under
test.
Perform the test in Normal Condition (NC) and in two different Single Fault Conditions (SFC):
1) earth open and 2) one of the supply conductors open at a time. Perform the test with normal
and reverse polarity.
NOTE: Refer to the instructions delivered with the safety analyzer to perform this test.

NOTE: *The measuring device (MD) represents the network and voltage measuring instrument
and its frequency characters according to IEC 60601-1.

1.

Configure the safety analyzer as follows (NC):

−

Polarity: NORMAL

−

Neutral: CLOSED

−

Earth (GND): CLOSED

2.

Power on the device under test.

«
...
111
112
113
114
115
...
»

Содержание CARESCAPE Monitor B450













































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для CARESCAPE Monitor B450

Бренд: Parker Страницы: 5

Бренд: Bacharach Страницы: 31

Бренд: Bacharach Страницы: 2

GPSMAP 188 Sounder

Бренд: Garmin Страницы: 134

Бренд: IBEX Страницы: 4

Бренд: tayco Страницы: 111

Varycolor MICRO 150HTI

Бренд: JB-Lighting Страницы: 18

Бренд: UNI-T Страницы: 4

UPO3000E Series

Бренд: UNI-T Страницы: 94

Бренд: UMS Страницы: 92

Бренд: Jumil Страницы: 78

Implantmed SI-1010

Бренд: W&H Страницы: 2

Бренд: K-SPORT Страницы: 5

Бренд: Bavis Страницы: 8

Бренд: Frick Страницы: 36

Бренд: Launch Страницы: 33

ThermoStable SIF-105

Бренд: Daihan Scientific Страницы: 41

Бренд: 2mag Страницы: 48

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды