GE HEALTHCARE CARESCAPE Monitor B450 Скачать руководство пользователя страница 81 | Manualshive

Страница: 81 / 236

background image

Configuration

73

2062973-003

SSID

Enter the Service Set Identifier (SSID),
also known as network name.

The SSID of the wireless client must match the
SSID of the wireless infrastructure.
A valid SSID includes up to 32 case-sensitive
ASCII characters, including space (ASCII decimal
32 to 126).

Confidentiality

Select the Confidentiality (Data
Privacy) method to be used:

- None
- WEP (64-bit)
- WEP (128-bit)
- WPA-PSK (TKIP)
- WPA2-PSK (AES-CCMP)

The confidentiality method of the wireless client
must match the confidentiality method of the
wireless infrastructure.
NOTE: The authentication method used with
WEP is Open System Authentication.
NOTE: The wireless MC Network supports only
confidentiality methods “None”, “WEP (128-bit)”,
"WPA-PSK (TKIP)" and "WPA2-PSK (AES-CCMP)"
NOTE: The S/5 Wireless Network supports only
confidentiality methods “None”, "WEP (64-bit)
and “WEP (128-bit)”.

Key Index

Select the Key Index to be used.

The Key Index of the wireless client must match
the Key Index of the wireless infrastructure.

NOTE: The Key Index is selectable only if the
confidentiality method selected is “WEP (64-bit)”
or “WEP (128 bit)”.

Pass Phrase / Key
Format

Select the Pass Phrase / Key Format:

- ASCII
- HEX

Select the format of entering a Pass Phrase /
Key Format.

WLAN Client Configuration

Item

Description

Comments

«
...
79
80
81
82
83
...
»

Содержание CARESCAPE Monitor B450













































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для CARESCAPE Monitor B450

Бренд: OMCA Страницы: 72

Бренд: Rangevision Страницы: 31

Бренд: Obdstar Страницы: 10

Бренд: MacDon Страницы: 272

Бренд: MacDon Страницы: 70

Бренд: FEAS Страницы: 72

Бренд: NEILPRYDE Страницы: 53

Бренд: JAC Страницы: 103

Бренд: 3Disc Страницы: 12

Бренд: 4iiii Страницы: 36

Бренд: 4iiii Страницы: 34

Бренд: 4EVAC Страницы: 27

Бренд: Cannon Страницы: 40

Бренд: NARGESA Страницы: 34

Бренд: PAS Systems International Страницы: 24

MARK V Alcovisor

Бренд: PAS Systems International Страницы: 20

Бренд: PARRY Страницы: 14

Бренд: York Fitness Страницы: 36

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды