manualshive.com logo in svg

GE HEALTHCARE CARESCAPE Monitor B450, Техническое руководство

Поделиться
Скачать
GE HEALTHCARE CARESCAPE Monitor B450 Скачать руководство пользователя страница 126

CARESCAPE Monitor B450

 118

2062973-003

The following sections describe the operation and interaction of the different subsystems.

9.1 Power Supply/ Power management subsystem

9.1.1 AC/DC Power Supply

Power Entry Module

The power entry module consists of an appliance inlet and mains filter. The fuses in the 
appliance inlet provide the input protection. AC/DC input cable provides the AC voltage to 
AC/DC power supply and protective earth connection to the device chassis.

AC/DC Power Supply Unit

The AC/DC power supply unit is a compact, medical, switched-mode power supply with a 
universal AC input. The high-efficiency design minimizes heat dissipation.
The AC input may vary between 90-264 Vac, 47-63 Hz single phase. It is designed to output 
15.7 Vdc ± 3% and 65 W continuous output power for the DC/DC board. 
The AC/DC power supply unit has overload and overvoltage protections.

AC/DC Output cable

The AC/DC output cable provides the 15.7 Vdc to the DC/DC board.

Batteries

The patient monitor supports two rechargeable and exchangeable (9-12.3V, 3800 mAh) 
lithium-ion batteries. They are located in the battery compartment. One battery must be 
installed at all times, the second one is optional.
The batteries support Smart Battery Data and they communicate with the DC/DC board using 
the System Management Bus (SMBus).
Battery charging and conditioning can take place either inside the patient monitor or with an 
external battery charger. 

Cooling

The patient monitor uses convection cooling. The ventilation openings of the device are located 
in the rear of the patient monitor and below the keypad.
The AC/DC power supply and the CPU assembly have integrated heat sinks to enhance the 
cooling of the patient monitor.

Содержание CARESCAPE Monitor B450













































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды